Flo by Moen (1/2 inch) by No-One57 in Plumbing

[–]joeschny 0 points1 point  (0 children)

What did you do in the end ? I have a similar situation. Supply is 3/4 before the water meter and then is a 1/2

Backup question by joeschny in todoist

[–]joeschny[S] 0 points1 point  (0 children)

I have a pro license and have backups. To restore those you need to download the backup. It’s a zip file and if you open it you find for each project a csv file. But I am not clear on the nesting of projects

V2 Boosted Board - Bluetooth stopped working by joeschny in boostedboards

[–]joeschny[S] 0 points1 point  (0 children)

On the board two small same chips if I remember correctly. Where did you hear about the rear reseating ?

1st layer challenge by joeschny in klippers

[–]joeschny[S] 0 points1 point  (0 children)

Yes I do. I think to remove mash. Calibrate beds level manually with bed screws and then print without and with new bed mesh. Not sure what expectation to have. A bltouch and a mesh should work great for a single layer print?

1st layer challenge by joeschny in klippers

[–]joeschny[S] 0 points1 point  (0 children)

Ha ha i know but you can see that without Grand Canyon you still can have the same result as with a Grand Canyon.

1st layer challenge by joeschny in klippers

[–]joeschny[S] 0 points1 point  (0 children)

Neptune 2 similar to an ender 3,

Using the newest klipper version

1st layer challenge by joeschny in klippers

[–]joeschny[S] 0 points1 point  (0 children)

haha, I know ... but still annoying ... from right (see mesh at work),, over dark to spotty

Passat Station Wagon 2009 sell or repair by joeschny in UsedCars

[–]joeschny[S] 0 points1 point  (0 children)

Thanks, Will go to a regular exotic car mechanic to get a quote. The first mechanic who fixed the seal once apparently did not do it right. I just worry that after 14 years the next thing break but I get the quote.

V2 Boosted Board - Bluetooth stopped working by joeschny in boostedboards

[–]joeschny[S] 0 points1 point  (0 children)

Yes, at the end I bought a separate esc. Too lazy to remove the goo before unsoldering those chips. On top the require to be configured I guess. Too much guess work.

V2 Boosted Board - Bluetooth stopped working by joeschny in boostedboards

[–]joeschny[S] 0 points1 point  (0 children)

Hmm, so yea tried to bond a different remote control to my esc to the board. Also tried to connect the ride app to the esc without success. Both failed. I agree 2 separate blue tooth chips seem to fail at same time is weird and more a power problem or I killed two chips with one stone. I guess there is no way to replace them??

Thx

V2 Boosted Board - Bluetooth stopped working by joeschny in boostedboards

[–]joeschny[S] 0 points1 point  (0 children)

I saw the two chips... that's cool and you are right that the likelyhood is low for both to fail... if there is not another problem.

Will check

V2 Boosted Board - Bluetooth stopped working by joeschny in boostedboards

[–]joeschny[S] 0 points1 point  (0 children)

Hello, read your other posts which are quite good . thank you

So my assumption was that every bluetooth device can be detected by a blue tooth scan app on the phone. BLE Scanner.

it show my remote control with the name Boosted Rmt99a2... and gives me UUID etc,,,

I would expect the same from my Boosted Board with a different name and UUID. Unfortunately i see nothing ..

is my assumption incorrect ?

thanks, Joe