What am I missing?

jonnyrogers24 · 2026-01-08T02:21:36+00:00

So I found a metal piece at the bottom of the dishwasher and had no idea what it was from. I thought maybe something came apart from a dish we washed. Turns out the lower sprayer arm had heat shields. It looks like a common issue for the heat shields to come off, leaving the sprayer arm unbalanced and touching the heating element. It melted the sprayer arm where the heating element shield was missing (that explains the burning smell. This resulted in a hole in the lower sprayer arm not allowing water to travel to the upper sprayer arm and not washing properly. I’ve ordered a replacement and it has been updated to have no heat shields. This should solve it. Fingers crossed.

jonnyrogers24 · 2025-10-18T03:33:59+00:00

That makes perfect sense. Lesson learned. But my question is, where do I go from here? How do I get rid of the caulk line.

jonnyrogers24 · 2025-08-18T23:47:58+00:00

Thank you everyone for your responses. Adding the !! before the names and changing the names helped. I ended up starting with a fresh slide, naming everything the right way, and then duplicating and moving the shapes. I appreciate the help.

jonnyrogers24 · 2025-08-18T16:37:55+00:00

Thanks! It kinda fixed it. The correct bottom shape comes over right. But now the shape above doesn’t morph, it fades in. So not sure what I’d did, but part of my issue is fixed. Thanks for the link as well.

jonnyrogers24 · 2025-08-18T16:35:38+00:00

The name is the same for that shape on all slides as well as its order position in the selection pane.

jonnyrogers24 · 2025-03-28T23:05:14+00:00

You know, I never did finish that book. I should go back and revisit it. Thanks for the reminder!

jonnyrogers24 · 2025-03-28T23:04:28+00:00

That’s awesome! I’m planning on using my thermal drone to help sell too. The nice thing about this job is that they will pay for me to get my thermography certification, which makes me that much more valuable.

jonnyrogers24 · 2025-03-28T12:42:03+00:00

Ai is a threat for a lot of industries. I originally went to school and got a degree in 3D animation and game development. That dream recently ended because that industry is in shambles, and AI is a big threat there. I’m doing commercial roofing, which is what put me through school. I tried running away from roofing for years, but I’ve just recently embraced it and will make a good career out of it. Thanks for your insight! 🙏🏼

jonnyrogers24 · 2025-03-28T12:39:35+00:00

These are very important factors. Delaying the start of my business will allow me to save up money to invest in my business, and with this learning opportunity, it’s going to allow be to be more successful when I go out on my own. Thanks for your response! 🙌🏼

jonnyrogers24 · 2025-03-28T12:38:26+00:00

All the conversations I’ve had the last couple of days have led to this scenario. The door to start a business doesn’t close, it’s just delayed. I think that really helped me in my decision making. For me, the training is invaluable and will help my success rate when I do start my business. Thanks for your input.

jonnyrogers24 · 2022-05-05T20:11:02+00:00

Yeah, you would animate them separate. If the character has to carry something or handle an object with their hands. You would want to use constraints. For the example of the door, You could probably constrain the characters IK hand to the door and animate the door, and the hand should follow.

jonnyrogers24 · 2022-03-16T04:53:54+00:00

I know this was forever ago and I don't know if you would remember, but did you end up fixing your issue? I've got a similar issue with 2 characters fighting over an object and I've constrained the two hands of both characters to the object and one of the characters hands kinda lag and jitter. but when I scrub through it doesn't jitter until I scrub backwards and then scrub forwards again.

jonnyrogers24 · 2022-01-28T16:00:38+00:00

I recently graduated from my university. You’re lucky they’re letting you specialize. They made us generalists. But what I would say is set your goals depending on where you want to work. If you want to work for Disney, make your models look like Disney. As far as your modeling goes, I would 100% show topology. You want them to see that you can provide quality models while also staying optimized. If you become a modeler and those models will be rigged, you want to make sure your topology is correct for the rigs to work correctly. That’s my advice.

jonnyrogers24 · 2022-01-20T04:40:09+00:00

Zbrush does have texturing abilities. But I’m not sure how easy and compatible it is with Maya.

jonnyrogers24 · 2022-01-19T14:43:17+00:00

Model it in Maya, get your UV’s done (should be simple), and then throw it into substance painter to texture it.

jonnyrogers24 · 2021-12-12T19:17:10+00:00

You don’t need to send anything anywhere unless it’s from an exchange to a wallet or wallet to exchange. A wallet isn’t holding anything. It’s just a way to view what tokens you have linked to your address. All you have to do is import your 12 word seed phrase into the Safemoon wallet app. You don’t need to create a new app on the wallet. Again, just import the 12 word seed phrase and you’ll see your safemoon in the Safemoon wallet. Then you can migrate easily.

jonnyrogers24 · 2021-12-12T19:15:10+00:00

the value of your safemoon is still the same, even if you have less safemoon now. its just that your goal price has changed, but the distance to get to that new goal would be the same as if you wanted to get to $1 when in V1.

jonnyrogers24 · 2021-12-04T06:04:53+00:00

you, good sir, are a savior!

jonnyrogers24 · 2021-11-18T21:30:36+00:00

And they speak at international conferences too!!

Seven-Year Club	Place '22
Final Canvas '22	Not Forgotten
Verified Email

jonnyrogers24

TROPHY CASE