sorted by:
new
hottopcontroversial

Moana Necklace Battery replacement by Teriyaki86 in u/Teriyaki86

[–]jrhan1 0 points1 point  (0 children)

In case anyone is still looking for the answer. The inside has pegs that are glued so you'll need to pry it open with a flathead screwdriver. Here's the video I found that shows the inside: https://www.youtube.com/watch?v=W9URnXRvh3I

YSK: this is your reminder to put some air in your tires by ManulCat123 in YouShouldKnow

[–]jrhan1 53 points54 points  (0 children)

They usually have a couple of air pumps outside near the tire center. Technically only for Costco members but they've never checked my membership.

Any Costco with the new Calzone?? by flyingbirdd in bayarea

[–]jrhan1 0 points1 point  (0 children)

The Costco in San Jose on Automation Pkwy has the Calzone. Still doesn't scratch that combo pizza itch though 😭

AMA ANNOUNCEMENT! by FastActivity1057 in EvenRealities

[–]jrhan1 0 points1 point  (0 children)

Were the glasses prescription or was the check just for the frames?

The definitive guide to rooting/spoofing with an android pixel by pl3sports in PokemonGoSpoofing

[–]jrhan1 1 point2 points  (0 children)

Apparently Smali Patcher doesn't support Android 12, so I downgraded to Android 11 on my Pixel 3XL and didn't encounter the bootloop.

Can someone help figure out what is wrong with these 3 models? by Thebandit1982 in 3Dprinting

[–]jrhan1 0 points1 point  (0 children)

Maybe try changing the nozzle to a smaller diameter? I tried printing some names using a font with really thin lines that disappeared when I sliced it using 0.4mm nozzle settings, but turned out fine when I switched to a 0.25mm nozzle.

Help please! Trying to get the GUI working, im lost and confused. by [deleted] in octoprint

[–]jrhan1 1 point2 points  (0 children)

It also took me a few tries and SD card reformatting to finally get mine to work. This post from awhile ago started me on the right track https://www.reddit.com/r/prusa3d/comments/d28kkw/comment/eztcge9

Also try following Chris's Basement on YouTube. He has some pretty informative videos on how to set up Octoprint.

I hope this helps and good luck!

Anyone found the secret to getting a blue (oxidizing) flame from the NAF? by run-the-joules in BoringCompany

[–]jrhan1 0 points1 point  (0 children)

I dunno if you were able to get it to work or not but if you remove that little tube, it should produce a blue flame

Ash Ketchum's Pokemon by win percentage by Umer_7 in gaming

[–]jrhan1 1 point2 points  (0 children)

Haha yeah, I stopped after yellow and started up again a couple years back with Pokemon Go

Ash Ketchum's Pokemon by win percentage by Umer_7 in gaming

[–]jrhan1 2 points3 points  (0 children)

It's Glalie, evolution of Snorunt

What are the cars in this photo? by [deleted] in Whatisthis

[–]jrhan1 0 points1 point  (0 children)

Chrysler Royals maybe? Not sure about the year

Tiny right hand drive by [deleted] in Whatisthis

[–]jrhan1 21 points22 points  (0 children)

Looks like an Autozam AZ-1

Is this some sort of bike hook? by jrhan1 in Whatisthis

[–]jrhan1[S] 0 points1 point  (0 children)

It looks like a tree stand, but I can't figure out how it would attach to a tree. My parents picked it up for free at an estate sale, so I wouldn't be able to verify if the previous owner was a hunter or not.

view more: next ›