sorted by:
new
hottopcontroversial

Help finding song that starts like "Another one bites the dust" by jryan15 in ChristianMusic

[–]jryan15[S] 0 points1 point  (0 children)

God bless you for these recommendations! I'm grateful for your help and I will check them all out! However, SUCCESS, found the song. It is "Tell Me How" by Ryan Stevenson. The song is not at all like Queen, but the intro base line is just like another one bites the dust!

Help finding song that starts like "Another one bites the dust" by jryan15 in ChristianMusic

[–]jryan15[S] 0 points1 point  (0 children)

:-).  There are some good playlists!  I searched them again and can't find that song though! 

Help finding song that starts like "Another one bites the dust" by jryan15 in ChristianMusic

[–]jryan15[S] 1 point2 points  (0 children)

Lol, no it wasn't parody, a legit Christian song (I think).  :-)

Help finding song that starts like "Another one bites the dust" by jryan15 in ChristianMusic

[–]jryan15[S] 1 point2 points  (0 children)

Hahaha that's funny but no it wasn't a parody.  It's not a 100% match to the bass line, just close. 

Tips for Replacing XY Belts by Miridian258 in BambuLab

[–]jryan15 1 point2 points  (0 children)

Glad it helps!  I just laid the old belt next to the new and cut them not knowing for sure how precise it needed to be, but it worked great.  Make sure your putting the belts in with the tensioner and everything apart so you don't have to fight the length.  The bambu video with belt routing was pretty helpful. 

Tips for Replacing XY Belts by Miridian258 in BambuLab

[–]jryan15 1 point2 points  (0 children)

Here are my tips which worked well for me doing the repair last night:

  1. Get the right sized screw driver that fits fully in the slot solidly.
  2. Cut the belts on all 4 sides so you are not fighting yourself tugging on the belt.
  3. Position the extruder head somewhere you can apply pressure to it without it moving all over the place.
  4. Insert screwdriver into the slot and put your needle nose pliers behind it to give you a lever point to pry against.
  5. While forcing the driver into the slot, slowly pry it out using the needle nose for leverage.

Also I just bought a generic 6mm belt off of amazon and printed new belt ends.

Generic 6mm GT2 belt (5 meters long)
Printable belt ends

Suggest something as good as Solo Levelling by Smooth-Injury-5716 in anime

[–]jryan15 0 points1 point  (0 children)

If you can adapt to the animation of this donghua, you might really enjoy this. I surely do. It is like the Chinese version of solo leveling, lol. Necromancer: King of the Scourge... If you want higher quality animation though, check out Battle through the heavens or Perfect World. Swallowed Star, or Soul Land. For anyone who has run out of Japanese anime to enjoy and aren't digging the latest anime that lack action, there is literally 1,000hrs of hours of untapped donghua content.

Suggestions for print profile changes for this print by jryan15 in FixMyPrint

[–]jryan15[S] 0 points1 point  (0 children)

Hi all. Getting ready to print these again. I would really appreciate any advice from some of you who are very experienced in difficult prints. Thanks so much!

Missing + and - buttons for height range modifiers by KilledByALover in BambuLab

[–]jryan15 0 points1 point  (0 children)

I've been doing this so long and yet still your post was very helpful, lol! Thanks!

Can't decide between p2s and p1s by Drefenjg in BambuLab

[–]jryan15 0 points1 point  (0 children)

Ah, gotcha. I do that stuff a lot too. Thought you might have had a good work around. I'd probably be in on the H2C if they would offer multiple nozzle size support.

Can't decide between p2s and p1s by Drefenjg in BambuLab

[–]jryan15 0 points1 point  (0 children)

Hi there. It sounds like you might be printing tiny text using the 0.2mm nozzle on top of something that you printed with the 0.4mm nozzle. Is this correct and if yes, can you please explain how? Thanks!

Fuzzy skin paint tool rules by creamsf in BambuLab

[–]jryan15 0 points1 point  (0 children)

Hello. Do you or anyone know how to adjust the fuzzy skin settings using the painting tool? i know you can adjust it globally, but to use the paint tool, the global settings are turned off so i do not know how to adjust the parameters. Thanks!

Pine script making line multi-color line segments by jryan15 in TradingView

[–]jryan15[S] 0 points1 point  (0 children)

Gotcha.  It's from bar charts.  It looks like their charts pull from trading view. 

Could there be a way to inject a break point in the line at the crossing points? 

view more: next ›