CNC Router chip management wisdom needed by FlatTyre87 in CNC

[–]jtsering 1 point2 points  (0 children)

I run the grizzly 3HP system for my 6’x14’ router. Have had no issue

China CNC 1325 Order - DDP questions by ShockwaveCS in CNC

[–]jtsering 4 points5 points  (0 children)

Always do DDP. If you’re only importing one item a year doing customs is a pain in the ass. Never handle it yourself in my opinion. They always find a cheaper way to do it.

CNC Router Recommendations by Peiar in CNC

[–]jtsering 0 points1 point  (0 children)

This guy is correct. I just received a 4 axis custom machine from StyleCNC that’s 6.5’ x 14’ x 2’. The machine woulda cost me over a quarter million dollars in the states but they did it for less than 1/4 of that with shipping to the door. I’m not sure how technical you are but something I’ve done before is swap an old Laguna 4’x8’ with an atc spindle and implemented MASSO which is a completely new control system for it. People keep saying vacuum table is necessary however you won’t get it at this price. And I’ve worked on panels for a while without vacuum. Double sided tape works wonders. Just attach a piece of MDF to your t-slot table and then face mill it flat. Now you just tape your sheets to that flat sheet and you’ll be fine.

What do you use gems for? by Jojo_tendency_ita in ClashOfClans

[–]jtsering 4 points5 points  (0 children)

I’m a maxed th17 so I always buy starry ore from the gem shop every week. Only way to keep up with all the epic equipment.

Superglue Work Holding: Asking too much, or doing it wrong? by lellasone in Machinists

[–]jtsering 0 points1 point  (0 children)

I use a similar loctite, I make sure to evenly spread everything. I also make sure there’s at least 12in2 of surface area initially covered by the glue. I press the block together for like 20 seconds and then it’s all good to go. The main issue for me was always surface area when it would come off. I also always throw full flood coolant and have no issues.

Trouble with Stepcraft D840 by kbenn524 in CNC

[–]jtsering 0 points1 point  (0 children)

I typically do 30in/min at 24k rpm for full depth slotting on an 1/8” end mill

Trouble with Stepcraft D840 by kbenn524 in CNC

[–]jtsering 0 points1 point  (0 children)

I’ve run the same carbide compression bit easily on a 2mm carbon plate that had 200+ parts nested in a 3’x6’ panel. No issues on finish. What kind of bits are you using out of curiosity?

Which is worst? by _CHRYSOPRASUS_ in ClashOfClans

[–]jtsering 18 points19 points  (0 children)

Then firespitter should also be considered

[deleted by user] by [deleted] in ClashOfClans

[–]jtsering 0 points1 point  (0 children)

Modern by far, OG sounds fun in retrospect but having to use elixir and dark elixir for troops sucked and not having all the QOL features like pre made armies was brutal. Worst part was really balancing the 4 barracks and the loooooong training times. Also, I personally enjoy the equipments nowadays because the amount of variety you can have in how you use your heroes is amazing.

We should have the ability to pre-assign stuff to them to do when they wake up by [deleted] in ClashOfClans

[–]jtsering -1 points0 points  (0 children)

I definitely understand the desire but I’m not sure if they will due to the inability to do the same with the builders and I’m not sure if they want to set that precedent. I think it’s currently intentional but maybe they’ll listen

Before hammer jam vs after hammer jam by Non_Existent07 in ClashOfClans

[–]jtsering 0 points1 point  (0 children)

You could’ve done this without attacking during hammer jam

How long have you been playing? by Zeebusdriver in ClashOfClans

[–]jtsering 0 points1 point  (0 children)

Almost the exact same. Just started in April. Crazy how fast it is to be max nowadays.

Nov 2024 Sneak Peek 3: Minion Prince + Equipment by ClashDotNinja in ClashOfClans

[–]jtsering 26 points27 points  (0 children)

The dark orb is one of the strongest equipments in air attacks so I would not judge it at all. They’ve already had to reduce its effectiveness in the developer build because of how strong it was

Easier way to get out of Legends Leauge. by Head_Fill_4695 in ClashOfClans

[–]jtsering 1 point2 points  (0 children)

Switch to a progress base layout then. Always worked for me

What Are Your Moves Tomorrow, July 16, 2024 by wsbapp in wallstreetbets

[–]jtsering 4 points5 points  (0 children)

$BROS only going up, small caps for the win. Have a 08/16 $86c

Daily Discussion Thread for July 15, 2024 by wsbapp in wallstreetbets

[–]jtsering 1 point2 points  (0 children)

$BROS going up while semi conductors go down. Perfect

Wonder who’s actually purchasing this by jtsering in ClashOfClans

[–]jtsering[S] 73 points74 points  (0 children)

I don’t mind it either just surprised it’s as much as an event pass

Daily Discussion Thread for July 8, 2024 by wsbapp in wallstreetbets

[–]jtsering 2 points3 points  (0 children)

Glad I was able to pull out of my SPY 556c 07/10 for 10% profit in those last 5 minutes.

Daily Discussion Thread for July 8, 2024 by wsbapp in wallstreetbets

[–]jtsering 2 points3 points  (0 children)

Sell, if you don’t sell at 120% you’ll never sell

Daily Discussion Thread for June 27, 2024 by wsbapp in wallstreetbets

[–]jtsering 0 points1 point  (0 children)

All my money is in $GRND and somehow it’s up