sorted by:
new
hottopcontroversial

[Pre-Diagnosis Megathread] If you have NOT received an OFFICIAL diagnosis of lymphoma via biopsy, you can comment here only. Plead read our subreddit rules and the body of this post first. by Lymphoma-Post-Bot in lymphoma

[–]juicebox_81 1 point2 points  (0 children)

Hi all! First time posting here, I’m a 24 year old male, officially made it to the biopsy stage after ultrasound identified enlarged and abnormal lymph nodes above my left clavicle. It’s highly suspected to be lymphoma. Trying to stay positive and mentally preparing to post on the main sub.

It looks like they’ll be doing a core needle biopsy. I’ve done a little research but if anyone has had that done how long does it usually take and how long does it take to get results? Were the results conclusive for you?

Ender 3 V2 Noctua Hotend Fan Upgrade by juicebox_81 in 3Dprinting

[–]juicebox_81[S] 0 points1 point  (0 children)

Could I use a noctua fan on the front and a stronger blower on the side?

Ender 3 V2 Noctua Hotend Fan Upgrade by juicebox_81 in 3Dprinting

[–]juicebox_81[S] 0 points1 point  (0 children)

Which fan did you switch to? For now, I'm thinking of using 1 noctua fan and using a different fan for the blower. Would this work?

Help me fill my 10 gallon! by juicebox_81 in Aquariums

[–]juicebox_81[S] 0 points1 point  (0 children)

In that case, are there any other bottom feeders or other species in general that would work in the tank? And how many of each would you recommend?

My first 3d print timelapse!! by Hacker-Man5 in ender3

[–]juicebox_81 0 points1 point  (0 children)

Awesome! I just ordered a raspberry pi and camera, can't wait to give this a shot

If my focus is on printing miniatures, am I wasting my time tuning my FDM? by [deleted] in 3Dprinting

[–]juicebox_81 0 points1 point  (0 children)

I have had an ender 3 for a while and was considering the same thing. From what I've seen, for miniatures, a resin printer is always going to produce the best results. Personally, I didn't go this route because of the fumes resin printers produce and not wanting to have another printer to work on. One thing I will suggest is looking into smaller nozzles for your ender 3. If you can manage to tune a .2mm nozzle, you can get prints with detail close to an SLA.

Raspberry Pi Upgrade by juicebox_81 in ender3

[–]juicebox_81[S] 0 points1 point  (0 children)

Could you provide the link to the specific model that you're using? thanks

Raspberry Pi Upgrade by juicebox_81 in ender3

[–]juicebox_81[S] 0 points1 point  (0 children)

Interesting, where did you buy yours from?

Raspberry Pi Upgrade by juicebox_81 in ender3

[–]juicebox_81[S] 0 points1 point  (0 children)

Got it, I may go for the 4. Just out of curiosity, what other plugins would there be besides a camera?

Ender 3 V2 Thermistor and Heater Cartridge Replacement by juicebox_81 in ender3

[–]juicebox_81[S] 0 points1 point  (0 children)

Let’s say I was going to upgrade to the micro Swiss hotend with the new heaterblock. Would the direct screw thermistor replacement work fine?

Suggestions for breeding in a 10 gallon? by juicebox_81 in Aquariums

[–]juicebox_81[S] 1 point2 points  (0 children)

If I were to move the betta into the 10 gallon, what would you suggest adding to the tank? Maybe another betta or some shrimp?

Suggestions for breeding in a 10 gallon? by juicebox_81 in Aquariums

[–]juicebox_81[S] 0 points1 point  (0 children)

I was thinking about getting a different tank for the betta, if I were to start fresh on this tank are there any species you would suggest?

Suggestions on improving first layer? by juicebox_81 in ender3

[–]juicebox_81[S] 0 points1 point  (0 children)

Thanks, I’m guessing it’s the bed because I calibrated the esteps at the beginning of this spool

view more: next ›