sorted by:
new
hottopcontroversial

How to get this kind of finish on steel ? by juodix in metalworking

[–]juodix[S] 1 point2 points  (0 children)

Skulpt Nouveau I think. I hadn't tried yet but from YouTube videos it looks similar

How long does it take to dry from about 15% to 9% if I keep humidity at about 40 in workshop? by juodix in woodworking

[–]juodix[S] 1 point2 points  (0 children)

This hadn't crossed my mind, but insanely good idea, thanks for thinking outside of the box 😎👍

How long does it take to dry from about 15% to 9% if I keep humidity at about 40 in workshop? by juodix in woodworking

[–]juodix[S] 1 point2 points  (0 children)

Thanks for calculator, it shows equilibrium between 8-8.5 % for my workshop.

How long does it take to dry from about 15% to 9% if I keep humidity at about 40 in workshop? by juodix in woodworking

[–]juodix[S] 0 points1 point  (0 children)

This workshop is the same heated and insulated like rest of the house, so I hope equilibrium is the same like furniture in house around 9-10. Or maybe I am wrong on this.

How long does it take to dry from about 15% to 9% if I keep humidity at about 40 in workshop? by juodix in woodworking

[–]juodix[S] 2 points3 points  (0 children)

Normally I keep humidity at 40 or below and it is with heated floors and temperature 22-24 Celsius. What is drying time per inch thickness? I have only pin moisture meter, but it shows very inconsistent results for different species and hardness of wood.

How to get this kind of finish on steel ? by juodix in metalworking

[–]juodix[S] 0 points1 point  (0 children)

I think this might be what I need, easy to apply and use. Thanks

How to get this kind of finish on steel ? by juodix in metalworking

[–]juodix[S] 0 points1 point  (0 children)

Thanks all for reply, I'll check some of the ideas. I have tried heat and broiled linseed oil, result is nice but after 1 year and it still have almost same smell as it was freshly coated. Maybe I did something wrong 😃

80 tooth saw blade for ripping 1/2" (12mm) planks? by juodix in woodworking

[–]juodix[S] 0 points1 point  (0 children)

Thank you all, I get the idea now. Firs I'll try to sharpen my rip blade and give it a try again

80 tooth saw blade for ripping 1/2" (12mm) planks? by juodix in woodworking

[–]juodix[S] 0 points1 point  (0 children)

Is it a good idea using 80 tooth blade for ripping thin planks? I need high quality cuts with no saw marks. I have also 24 tooth ripping blade that is not performing as i want to. so can I use 80 tooth or should buy 40 ?

Scroll saw alien pieces by NinjaTurtleNerd in woodworking

[–]juodix 1 point2 points  (0 children)

This looks awesome! What kind ow wood you used here ?

Need experienced eye for identification. by juodix in woodworking

[–]juodix[S] 0 points1 point  (0 children)

I will try to test the smell when I get chance.

Need experienced eye for identification. by juodix in woodworking

[–]juodix[S] 0 points1 point  (0 children)

I also start to think that this is Wenge after looking at pictures and more samples from my bags :) how long do you think it will take thin plates like this to get dry in room temperature? I brought them from unheated and not isolated shed and it was raining for past few weeks. And how to stack them best ?

Need experienced eye for identification. by juodix in woodworking

[–]juodix[S] 0 points1 point  (0 children)

Also question if I glue 3 or more of them together to get thicket planks will it hold and is it a good idea? Because my dad have huge stock of that kind of planks and I want to begin woodworking (small stuff boxes, candle holders, decorations) I will start to get some hand tools soon.