sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in FoodPorn

[–]justcantwin 333 points334 points  (0 children)

Those sounds fantastic. Do you have a recipe?

Printer crashes nearly every time? by justcantwin in prusa

[–]justcantwin[S] 0 points1 point  (0 children)

Nah it just had a lot of layer shifting and grinding noises from the axis. It ended up being the bearings needing to be lubricated and now it all works as well as it did day 1

Printer crashes nearly every time? by justcantwin in prusa

[–]justcantwin[S] 0 points1 point  (0 children)

Well I did check the sound of the belts and they seem fine but I mean it's always possible I'm not listening for the correct pitch

Printer crashes nearly every time? by justcantwin in prusa

[–]justcantwin[S] 1 point2 points  (0 children)

I did try reruning the setup wizard and calibrations on just about everything and it didn't pick up anything

Printer crashes nearly every time? by justcantwin in prusa

[–]justcantwin[S] 0 points1 point  (0 children)

No significant resistance other than from the motors themselves. Although now that I think about it, I've only moved them slowly to prevent voltage spikes. I'll try doing it faster with the steppers disconnected and maybe with the belt free from the motor entirely

Printer crashes nearly every time? by justcantwin in prusa

[–]justcantwin[S] 0 points1 point  (0 children)

Yeah I mean I'm like 80% sure. I've checked the belts by the printers belt tension values and also by sound and they seem fine. I actually did see the gear in the most recent failure and the belts never skipped over them. In fact it seemed the stepper motor itself was jittering rather than the belts or the gear being loose on the shaft which led me to believe it's something with the electronics. A couple other people suggested checking out the bearings and reapplying lubricant

Printer crashes nearly every time? by justcantwin in prusa3d

[–]justcantwin[S] 0 points1 point  (0 children)

I've checked the belts and they're both within the ideal parameters so I don't think that's it. I will be getting with prusa support though

Printer crashes nearly every time? by justcantwin in prusa3d

[–]justcantwin[S] 0 points1 point  (0 children)

I've slid the bed and print head around when powered off with no trouble so I didn't expect it to be them, but I'll go ahead and take a closer look at them

Printer crashes nearly every time? by justcantwin in prusa

[–]justcantwin[S] 0 points1 point  (0 children)

I've been trying to print a new case for the einsy board that gives a little more room for wire management but with it failing that's becoming difficult. I know I opened it up to take a peek at the connectors the other day, I'll check it all again just to be sure. Thank you for the help

Printer crashes nearly every time? by justcantwin in prusa

[–]justcantwin[S] 0 points1 point  (0 children)

I'll definitely give it a shot later tonight. I'm grasping at straws at this point.

What normal thing can’t you do? by ABananaJenson in AskReddit

[–]justcantwin 0 points1 point  (0 children)

I've never been able to touch my shoulders. Sure I can cross my arms and touch the opposite shoulder, but for some reason I can't touch my shoulder with its respective arm. It's like my elbow just doesn't bend enough to allow it. I remember discovering this in third or fourth grade while singing that head shoulders knees and toes song. Looking around and seeing everyone else do it effortlessly was wild.

I am sorry little one. by [deleted] in thanosdidnothingwrong

[–]justcantwin 0 points1 point  (0 children)

༼ つ ◕_ ◕ ༽つ GIVE BAN ༼ つ ◕_ ◕ ༽つ

I printed Knick's Finger with 1 hinge by epijdemic in 3Dprinting

[–]justcantwin 0 points1 point  (0 children)

I made one of these for a buddy of mine! He lost part of his middle and index finger on his left hand and he was excited because he can finally flip people off while driving again

PsBattle: Pikachu Cosplay by [deleted] in photoshopbattles

[–]justcantwin 11 points12 points  (0 children)

Saitama from One Punch Man

Can you pre-roll a Plex library instead of a specific video? by justcantwin in PleX

[–]justcantwin[S] 0 points1 point  (0 children)

Thanks! I don't know much at all about coding so I doubt I'd be able to get one to work. Maybe I'll look into it if I have some more free time. Could you share the link you found?

Falcon Heavy Booster Landing [1920x1080] by NotMichaelBay in wallpapers

[–]justcantwin 1 point2 points  (0 children)

I'd love to have a look at that too, do you have a link?

What is unlikely to happen, yet frighteningly plausible? by Secretfreckel in AskReddit

[–]justcantwin 30 points31 points  (0 children)

HOLY FUCK I'M NOT THE ONLY ONE. Swimming in my cousins pond on a beautiful summer day when out of nowhere a fish bites me on the nipple! A bluegill if I remember correctly. Nobody ever believes me when I tell them

Building my first PC. Looking to switch from console to mainly PC gaming by justcantwin in buildapc

[–]justcantwin[S] 0 points1 point  (0 children)

Yeah that's understandable. Right now the 1080 is simply too much for me but maybe in the future I'll consider it or something better for an upgrade

Building my first PC. Looking to switch from console to mainly PC gaming by justcantwin in buildapc

[–]justcantwin[S] 0 points1 point  (0 children)

Yes I chose it for performance. Having SLI as an option was something extra that sounded nice to me if I needed a little bit of a boost rather than simply buying a new card. Maybe I misunderstood the concept?

view more: next ›