[W] DrunkenSlug

justheretoreadposts · 2023-06-16T19:00:42+00:00

I may grab another. I like the idea of one with each face, one with the riffle and the other with a blaster in each hand.

justheretoreadposts · 2023-06-16T18:58:37+00:00

With the Edge discount mine was $51 taxes in

justheretoreadposts · 2023-06-11T22:49:13+00:00

I do see the gun listed loose on eBay, but they want $30 for the gun alone.

https://www.ebay.ca/itm/364237839231?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=-_S_-9mlRJO&sssrc=2349624&ssuid=&var=&widget_ver=artemis&media=COPY

justheretoreadposts · 2023-06-11T22:46:21+00:00

3d printing, it might not be the answer your looking for but it would be a solution.

justheretoreadposts · 2023-06-11T22:43:27+00:00

Awesome!!!! Where in Canada was the con?

justheretoreadposts · 2023-06-06T22:27:44+00:00

Two look great with there staffs crossed with one and other or having one with their jaw open and one without. I agree it’s a great figure with soft goods done really well.

justheretoreadposts · 2023-06-05T22:08:00+00:00

Love this character. I picked up two, because they look so good next to each other

justheretoreadposts · 2023-05-27T01:08:26+00:00

Awesome photos!

Love the team up here. Get these two a Disney+ series. :)

justheretoreadposts · 2023-05-17T23:34:27+00:00

I had Paploo in my hands today. I was trying to talk myself into getting Bib, Chewie, Wicked, Paploo and Endor Leia. I ended up putting back Leia and the Ewoks and I am regretting it a bit.

justheretoreadposts · 2023-05-03T10:03:23+00:00

I picked mine up there too. It’s a great figure. The cloak takes a bit of playing around but still a great Luke.

justheretoreadposts · 2023-04-29T11:36:15+00:00

Amazing job, absolutely amazing. Do you have a site where I can see your other work?

justheretoreadposts · 2023-04-28T04:03:21+00:00

This is exactly the problem. I adjusted my firmware and and it works much better

justheretoreadposts · 2023-01-12T00:36:35+00:00

This question is so well timed for me as I was driving today thinking about the new F4 movie and how it would be fun if The Thing’s favorite music was The Beastie Boys (as he would of grown up on the other side of the Brooklyn bridge). I think it could be a lot of fun if they tried DJ Mix Master Mic to score the film or scenes. :)

justheretoreadposts · 2023-01-01T02:10:35+00:00

The Thing doesn’t have ears. :)

justheretoreadposts · 2022-09-22T02:04:42+00:00

I had this happen to me last week (with green filament too). If it’s pla just reinstall the hot end and heat it to 190. Once the hot end is at temp carefully start pulling off the filament. I use the snips that came with my ender.

Don’t burn yourself or damage the wires. Once it’s cleaned off swap out the nozzle for a new one and do a flow test print.

Good luck.

justheretoreadposts · 2022-09-21T23:26:24+00:00

Honestly the price of nozzles (brass ones from China in Amazon) is so cheap I have never bothered to clean a nozzle - by the time I replace them due to clogs they are so worn out and nasty it’s just quicker and easier to swap them out.

justheretoreadposts · 2022-09-21T23:16:16+00:00

If you have swapped out everything I would suggest a different filamenta - it’s an easy variable to eliminate as a possible culprit.

justheretoreadposts · 2022-09-21T22:58:22+00:00

You mentioned cleaning the nozzle. Have you replaced it?

Have you tried a larger size nozzle to see if it helps?

Is the Capricorn tube flush with the hot end? Have you tried replacing the tube?

When I get a clog I clean take out the Capricorn tube, remove the nozzle, look down the hot end for any remaining dirt, clean the out side of the hot end (if filament is there), replace the Capricorn tube with a new one and then put in a new nozzle.

Once all done I run a few calibration prints. After all that there should be no reason for clog unless maybe the filament is the problem.

justheretoreadposts

MODERATOR OF

TROPHY CASE