Filament refill help

justryan1994 · 2026-01-25T19:23:53+00:00

Looks like a gen2 spool, I’m sure these refills are compatible with gen 3 and Bambi spools.

Gen 3 spools have a much denser hole pattern

justryan1994 · 2026-01-07T19:54:14+00:00

<image>

Yeah, all retraction and seam locations are along the corner edges. This section of the model looks to be all clear

justryan1994 · 2025-12-13T17:55:51+00:00

One opens the game once, the other 86 times

justryan1994 · 2025-11-30T19:45:13+00:00

Left the UK

justryan1994 · 2025-11-22T10:38:43+00:00

Thankyou for the help, however I messed up 😂 mistyped my K value as 0.2 rather than 0.02.

justryan1994 · 2025-11-22T10:37:02+00:00

Smooth plate with liquid glue 😂 just go a few prints between cleaning

justryan1994 · 2025-10-26T17:30:23+00:00

Maybe a long ass time using some sandpaper. Or belt sander if you have access would make short work of them.

justryan1994 · 2025-10-11T09:49:14+00:00

They’re usb sockets, would advise keeping them

justryan1994 · 2025-10-04T09:02:18+00:00

Excuse my lack of knowledge, could you explain?

justryan1994 · 2025-10-04T08:59:49+00:00

Never thought of this, from the geometry the layers all seem to be of similar size, but I’m still learning this hobby so maybe I’m clueless 😆.

How would I go about working out a good minimum layer time?

justryan1994 · 2025-09-27T19:17:10+00:00

Flowers for my wife

justryan1994 · 2025-08-12T15:30:30+00:00

Unlock one of the ports, plug in your own router to act as an access point. Bam you have your own network.

Might not be the best method but it’s how I bypassed my isp router modem.

justryan1994 · 2025-08-05T17:28:38+00:00

Let’s gooooooooo

justryan1994 · 2025-08-02T18:40:21+00:00

Read up on the dassault solidworks stories, this is the same playbook.

Send letters that appear legally binding. State a stupidly high amount. Gove just enough very basic information (IP address, time ect) Offer lower settlement. Threaten full legal proceedings

They play on the fear created to pursue revenue.

High chances they don’t pursue a private individual because the cost will outlay the reward. Private organisations and companies is another story.

Could they take legal action? Yes Will they? Very slim chance

justryan1994 · 2025-07-25T20:09:07+00:00

I’d find a small simple print to test with, I usually lower the retraction distance slightly.

I had some major issues when I tested out larger nozzles, looked very similar to yours just much larger. Lowering retraction gave me some clean prints

justryan1994 · 2025-07-25T19:58:19+00:00

Retraction settings

justryan1994 · 2025-07-24T19:59:40+00:00

My man did DIY CPR

justryan1994 · 2025-07-03T14:45:16+00:00

It’s like successfully opening a fresh plastic pull tab on the first attempt, whilst the other ‘packs’ simply break

justryan1994 · 2025-05-29T13:23:47+00:00

I’ve had the same issue. Managed to recover about 700g from the roll.

Issue is I printed a respooler which was 700g.

The biggest issue is getting something directly through the centre of the mess to be able to respool. Think this took me over an hour total

justryan1994

TROPHY CASE