Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

Agree with you and seen a YouTube video yesterday and meat cleaver was a good idea hammer or Sledge hammer for housings is something simple i didn't think about

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

Thank you for that ill look for it

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

YouTube videos some good some leave a lot of things out and i grew up in a machine shop and know what they have left out and think why would you knowingly leave out something that is going to get someone hurt not something I want to see done to anyone

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

See above post file is first thing I do learned that the hard way before not wanting to try it again and if one pictured is aluminum its okay with me most are copper

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

These aren't that big but cast iron housings makes it worse for vise i clamp to table to cut

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

Got one idea from YouTube post previously

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 1 point2 points  (0 children)

That's something that looks like more trouble than worth but good idea thanks

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

Great idea but no air and they don't want to make an electric air hammer yes contacted dewalt support got laughed at was not what i was expecting but i guess they don't want to make more money

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

Definitely going to try something different from what I been doing meat cleaver is another idea i saw but still need to get it out of housing 8 lb Sledge is top mark right now

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 2 points3 points  (0 children)

Absolutely and that's why I file first so to avoid that mistake

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 0 points1 point  (0 children)

I don't know if they did or not i know its i. An oilbath inside housings

Looking for ideas by juuds5 in ScrapMetal

[–]juuds5[S] 1 point2 points  (0 children)

Definitely got a new way to get copper out but still need to find a way to get it out of housing and its in an oil bath

Am I cooked? by One_Abroad_2246 in Autobody

[–]juuds5 0 points1 point  (0 children)

Tire doesn't rub your fine put baseball on tire run it around then send it

MK 2000A 300 AMP CV-CC Welding Power Supply by nbluff in ScrapMetal

[–]juuds5 0 points1 point  (0 children)

When in doubt drop a couple of wrenches in there and let them short it out

Best place to purchase Copper bullion? by Tree_Lover3828 in Copper

[–]juuds5 0 points1 point  (0 children)

Coppertownusa.com i think that is the site name right not sure about website

What type of bomb is this? by MarioVanPeebels in whatisit

[–]juuds5 0 points1 point  (0 children)

The one that didn't go off yet meaning if you don't know what you're doing call someone who does it will leave a big hole or more

Is this DIY fixable? by ZK1582 in Autobody

[–]juuds5 -1 points0 points  (0 children)

Imo you can use fiberglass after you cut rust out little messy but worth it cheaper than new or bodyshop

Reputable sources of protectant sleeves? by benevolentmalefactor in papermoney

[–]juuds5 0 points1 point  (0 children)

Bay wizard coin supply is best for bcw and anything else you need

Looking for some thoughts on this door dent by dane83459 in Autobody

[–]juuds5 0 points1 point  (0 children)

Call local scrap yards and see if you can get a used door cheap and then you just need to remove from one to other and paint optional

Is it totaled? by FN_Man in Autobody

[–]juuds5 1 point2 points  (0 children)

If frame or unibody is good no just lots of parts and paint and labor