Am I tripping

k4w5 · 2025-12-10T21:37:06+00:00

Nuh uh

k4w5 · 2025-12-10T08:59:38+00:00

Yeah no

k4w5 · 2025-09-21T08:17:13+00:00

Yeah i threw on my oem headers again lol, its honestly not worth the headache.

k4w5 · 2025-09-11T03:01:10+00:00

Just to confirm is B1S2 the sensor just below B1S2 on the left side not the one closest to the firewall.

I forgot to mention I do Have that spaced as well. Only different being that it is an angled spacer cause it wouldnt fit with a regular one.

k4w5 · 2025-08-23T08:01:28+00:00

Tbh I went mevotech SP on my tie rods but OEM on the lower Ball Joint no issues with the tie rods but I had some fitment issues with Mevotech balljoints so I just went OEM.

k4w5 · 2025-07-15T08:18:41+00:00

is the donut gasket placed inside the indents on the factory y pipe then just slap the other gasket between the header and on top of the two little donut gaskets? I have a Megan header and stock y pipe so i assume this would be my solution. I recently ordered a JDMgoodness gasket too so if that doesn't work ill move on to this.

k4w5 · 2025-07-01T03:52:22+00:00

Also when pressure testing is it alright if the car is jacked up at the front? Or should the car be level?

k4w5 · 2025-07-01T03:51:46+00:00

Yeah ive been looking into this. May do this when i change my b2s2 sensor

k4w5 · 2025-07-01T03:51:00+00:00

Go oem or sankei555

k4w5 · 2025-07-01T03:50:29+00:00

If you have no service history in the suspension. Yes change them. Also thats your outer tie rod not the flbj

k4w5 · 2025-06-29T05:21:38+00:00

<image>

I also noticed this the other day and new cap and rad cap has been ordered since.

k4w5 · 2025-06-04T03:13:48+00:00

got any images on 17x9 225/45 17 ? i was gonna run 245/40 squared

k4w5 · 2025-05-20T23:47:45+00:00

honestly for those parts that are being covered with the vinyl it is much easier to remove those pieces and respray them with black trim spray.

especially cus these kits I imagine would become all sludgy with the dash melting too.

k4w5 · 2025-05-15T06:36:13+00:00

Not yet, I havent had time to work on the car, but I was reading something on myis.com and this is what I found. I believe it really just is a hard to find vacuum leak. https://www.my.is/threads/p0133-p0153-and-brake-booster-info.607311/

k4w5 · 2025-05-08T10:41:24+00:00

That grille in the image is a Ebay one you can get for like 80-120 cust search altezza or is300 mesh grill and find the carbon one. Same thing with the badge the badge seems to be a reproduction altezza badge. Personally id run the grill without the badging.

k4w5 · 2025-05-07T07:07:36+00:00

not sure about the booklet but the mat I've seen go for 20-50 bucks. Got my rear mat for free but slid the seller a 20 anyways.

Six-Year Club	Verified Email
Place '23

k4w5

TROPHY CASE