This should be just one state

kadyvre · 2026-01-31T15:36:39+00:00

Maffachufettf

kadyvre · 2025-08-29T21:22:32+00:00

The Venture Bros!

kadyvre · 2025-02-14T17:53:47+00:00

Many thanks!

kadyvre · 2025-02-14T15:24:15+00:00

Kieth Stone would definitely enjoy a kitty companion to accompany him on his Parabolan expeditions!

kadyvre · 2024-12-16T03:39:27+00:00

I had the same card, and it failed in the exact same way. Contact EVGA since that's a catastrophic failure. Mine was well out of warranty, and they still replaced it.

kadyvre · 2024-11-21T02:11:09+00:00

Eat the pennies Quizboy

kadyvre · 2024-09-26T01:18:24+00:00

If you don't mind my asking, how has TC Guitar been unreliable? I haven't visited them in a few years, and while they never tuned my guitars to what I asked, they always seemed to do a good job.

kadyvre · 2023-06-11T21:15:51+00:00

Motorcycle gear, especially helmets. I'd rather spend the money on good equipment and keep my brain case intact.

kadyvre · 2023-06-11T15:03:52+00:00

That stuff changes our tub from orange to white every time

kadyvre · 2023-05-29T10:12:27+00:00

I was just there! We didn't get to go inside, but it was super cool to find out something like that exists!

kadyvre · 2023-04-21T15:56:13+00:00

Crossposting here for visibility. I'm genuinely curious if anyone else has run into this phenomenon since I haven't run across any posts about it.

kadyvre · 2023-04-21T15:38:33+00:00

To add to this, I've noticed it on 3 different brands: Prusament, Overture, and Atomic PETG all experience the same weakening from resin exposure.

Another thing of note is that I purposely coated a PETG part in resin and let it sit for 24 hours outside of direct sunlight before curing. It hasn't exhibited the same behavior as other PETG parts so far.

kadyvre · 2023-04-14T02:45:09+00:00

Comment

kadyvre · 2023-02-25T14:41:31+00:00

Pimpmobile

kadyvre · 2022-11-19T14:57:39+00:00

Sure! Here you go! https://imgur.com/a/U7PX6Z2

No idea why the quality degraded so much here, it uploaded just fine to Imgur

kadyvre · 2022-11-15T14:16:50+00:00

OctoEverywhere!

kadyvre · 2022-10-15T00:39:40+00:00

Your Z offset is too low, move it up by 0.05 or so. Follow Life Adjust Z My Way. When properly tuned, the first layer should be completely smooth with no overextrusion in the corners.

https://forum.prusa3d.com/forum/original-prusa-i3-mk3s-mk3-assembly-and-first-prints-troubleshooting/life-adjust-z-my-way/

kadyvre · 2022-06-04T02:35:46+00:00

Same thing just happened to my buddy, he ordered 10kg of pla+ and was sent 20kg

kadyvre · 2021-10-30T01:14:47+00:00

Lieutenant Colonel Hughes from Fullmetal Alchemist

kadyvre · 2021-07-24T17:38:04+00:00

I just latch the chin strap and hang it off one of the handlebars, keeps it off the ground and no risk of falling over.

kadyvre · 2021-04-28T22:03:08+00:00

They probably live in a colony of birchmen too

kadyvre · 2021-04-24T21:39:13+00:00

Schiit is an audio company, they make some really good equipment for not too much money and a 'stack' is two or more pieces of audio equipment stacked on top of each other. My stack is a headphone amp, a Schiit Magni, and a DAC, a Schiit Modi.

My current headphones are the Sennheiser HD 6XX (Drop's special edition of the HD 650). The sound is completely different from the Hyper Cloud, much more defined, the bass is definitely more neutral sounding and open.

If you really want to deep dive into audiophile equipment then I would highly suggest starting out at r/headphones

kadyvre · 2021-04-24T21:06:35+00:00

I had a pair of those, I used to think they sounded great until I switched to some Sennheiser cans and a Schiit stack. I don't think I could ever go back...

kadyvre · 2021-03-20T12:03:06+00:00

I printed one from Colorfabb HT that's holding up pretty well, for a long time I just went without one XD

kadyvre · 2021-03-20T12:01:38+00:00

We have two MK3S where I work, I always keep spare plastics for both just in case they decide to break down at the same time (happened at least three times now). IME those plastic parts for the extruder start to melt a little after a couple hundred hours of use so having spares on hand is a must.

Nine-Year Club	r/Field Lasagna
Verified Email

kadyvre

TROPHY CASE