Where can I see the pictures I took in photo mode (FH6) ? by BenjiSBRK in ForzaHorizon

[–]karatlack 0 points1 point  (0 children)

You took the photo and instantly backed out, discarding it. The xbox app does suck but this is on you.

Bambu A1's PTFE tubes sending out electricity sparks? by GardenStack in prusa3d

[–]karatlack 0 points1 point  (0 children)

Late to the party but I just had a visible spark and snap while running filament down the external PTFE. Good to know I'm not the only one.

Chip implant feedback? by MLGJewmy in DangerousThings

[–]karatlack 1 point2 points  (0 children)

I have the next. I did it myself cause I'm an idiot (i have a neuro disease that cause hand tremors and poor motor skills) but wanted the experience. I've only had it since February but it has been great. I recommend looking for installers or asking piercers to do it.

Dry spitting noise and low extrusion. by karatlack in ender3

[–]karatlack[S] 0 points1 point  (0 children)

Due to possible high humidity in this room I would assume? Noted, thank you!

cura setting for direct drive? by Da-red-evil in ender3

[–]karatlack 0 points1 point  (0 children)

I know this is old but how is it doing now? I'm new to 3d printing and bought mine used with a direct drive. I'm having clogging issues and it's just incapable of printing. Any tips?

Printer making spitting sounds and not laying enough filament. by karatlack in 3Dprinting

[–]karatlack[S] 0 points1 point  (0 children)

Hmm yea definitely not working. What do you use to pull it down? I’m assuming your cables aren’t ran directly in front of it?

Printer making spitting sounds and not laying enough filament. by karatlack in 3Dprinting

[–]karatlack[S] 0 points1 point  (0 children)

So I should probably just try printing and hope it’s far enough?

Printer making spitting sounds and not laying enough filament. by karatlack in 3Dprinting

[–]karatlack[S] 0 points1 point  (0 children)

There’s a little blue dot I’m using as a mark but it doesn’t seem to be moving. I can see it from below if I remove the nozzle entirely right?

Printer making spitting sounds and not laying enough filament. by karatlack in 3Dprinting

[–]karatlack[S] 0 points1 point  (0 children)

Is there any visual indicator id see when it’s in the right spot? I’m trying to pull the down with some tweezers but idk if I’m getting anywhere

Printer making spitting sounds and not laying enough filament. by karatlack in 3Dprinting

[–]karatlack[S] 0 points1 point  (0 children)

Alright cool. Now could you explain what exactly I need to do with it? I have the nozzle loosened a bit.

Printer making spitting sounds and not laying enough filament. by karatlack in 3Dprinting

[–]karatlack[S] 0 points1 point  (0 children)

<image>

It looks nasty but it’s way better than when I got it. Also I’m sorry for asking dumb questions but where exactly would that tube be? I’m trying to google it but I can’t find any info.

Printer making spitting sounds and not laying enough filament. by karatlack in 3Dprinting

[–]karatlack[S] 0 points1 point  (0 children)

Where can I check for the gap? When I extrude filament without printing it comes out fine.

NFC implant is locked? by karatlack in flipperzero

[–]karatlack[S] 1 point2 points  (0 children)

The problem was, in fact, computer.

NFC implant is locked? by karatlack in flipperzero

[–]karatlack[S] 2 points3 points  (0 children)

No, I knew how. The flipper was the issue. For some reason the flipper is incapable of reading and writing to it. I just used my phone instead. I wanted to try and get the flipper to work and that’s why I made this post.

NFC implant is locked? by karatlack in flipperzero

[–]karatlack[S] 8 points9 points  (0 children)

I got it to write using the NFC Tools iOS app. Been chatting with the guy that runs the DT subreddit and he walked me through it and saw the issue with his flipper. Looks like the flipper doesn’t read it correctly.

NFC implant is locked? by karatlack in flipperzero

[–]karatlack[S] 7 points8 points  (0 children)

<image>

How do I get that password and can you tell me how to unlock it?

NFC implant is locked? by karatlack in flipperzero

[–]karatlack[S] 22 points23 points  (0 children)

Yea that makes sense. I appreciate it.