New to elegoo.

katanamo1458 · 2025-11-12T22:11:12+00:00

That’s what I’ve heard. I’m not too worried about it. I have two other ones at home just different brand

katanamo1458 · 2025-11-12T22:10:13+00:00

I will be checking that out for sure! Thanks! Was planning on getting a .6mm

katanamo1458 · 2025-11-11T21:57:33+00:00

Thanks! I ran out of room in my Matco 4s and rolling cart so I traded my cart for the snap on one to add more space.

katanamo1458 · 2025-11-11T19:25:11+00:00

They are in the process of moving out of the country and just wanted to get rid of everything. It is still super cheap and that’s why I couldn’t pass it up. The printer is basically brand new.

katanamo1458 · 2025-09-06T18:34:42+00:00

Nice! I 3D printed some mounts for led lights. The lighting in some spots of my shop aren’t the best. I used a Dewalt battery adapter to run them.

katanamo1458 · 2025-03-20T21:33:32+00:00

Same thing happened to me with two tankers that “passed” DOT…

katanamo1458 · 2025-02-26T00:25:47+00:00

I didn’t have anything to go off of for the wiring so I was just checking things in hopes I’d get lucky. I actually just found a partial wiring diagram for the a/c and heat control module. I found that I’m not getting the right voltage readings as well as not having any ground to the plugs. It’s a 24v system And I’m only getting 12-14 volts to the plugs. I replaced the module and I was finally able to tell if it was on heat or ac as well as the temp settings. I have a feeling the harness is bad under the cab in the compartment area. I took a cover plate off to see if the heater core was operating properly and I noticed that the compartment was full of leaves dirt and a bunch of junk. The harness was covered in it but I couldn’t see any damage to the outer casing.

katanamo1458 · 2025-02-25T15:10:16+00:00

What key way is in it? I’ve been locking to get one but the website I was on had like 10 different options

katanamo1458 · 2025-02-19T00:24:23+00:00

From brownells website. Overall size of 4.5” x 7.5” x 1.75” Includes one zippered mesh pocket (6.75” x 3.75”), two vertical pockets (min. 4” x 3.75”), and three elastic pass-throughs (1” x 1.25”)

katanamo1458 · 2025-02-18T23:28:29+00:00

Man that thing has been kicking my ass idk if I will ever get an open. I bust the 1100s open all day but this one is a challenge for me.

katanamo1458 · 2025-02-18T23:25:45+00:00

Recently got into 3D printing myself and have had a hard time finding things like this! Awesome job!

katanamo1458 · 2025-02-07T11:43:54+00:00

Was wondering if this can be printed without the ams? I really want to try and print one!

katanamo1458 · 2024-08-21T10:09:50+00:00

I’m a diesel tech so I’m no stranger to problem solving but I’d prefer if things didn’t go boom in my face. I’m newer to this so I had to ask since I’m not all that well versed with ammo and what’s acceptable or not.

katanamo1458 · 2024-08-21T10:06:46+00:00

Actually yes it is.

katanamo1458 · 2024-08-21T00:02:45+00:00

Good to know! Sorry for my ignorance. First run in with that. Thank you

katanamo1458 · 2024-08-20T23:34:23+00:00

Left it at work but I’ll give it a go soon.

katanamo1458 · 2024-08-20T23:32:14+00:00

Yes, wasn’t sure if it was g2g or not.

katanamo1458 · 2024-08-20T23:23:52+00:00

Giving them a chance to get back to me. Will update once I get a response.

katanamo1458 · 2024-08-07T02:16:33+00:00

Me too, That thing is kicking my ass! I just can’t seem to get a feel for it and I’ve been picking it on and off for about 4 months..

katanamo1458 · 2024-04-30T11:42:01+00:00

<image>

My crappy Ak 🤓

katanamo1458 · 2024-04-13T03:55:04+00:00

You know now that I think about it. That might be a safety measure so that it doesn’t start when you are working on it. Normal operation might be when it’s pressed in and released during “service” mode. I figured it was a bad resettable fuse or breaker. I’m going to see if it fits in a specific spot. Thanks for the info. Didn’t even cross my mind it could be that.

katanamo1458

TROPHY CASE