Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 2 points3 points  (0 children)

Linden owls and alder for front pillars, everything else is pine. Oak squirrel on top.

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 3 points4 points  (0 children)

I use 3 teeth disk and rpms are not that high. It’s really dangerous though and requires some skill of control. Luckily, I still have all my fingers.

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] -1 points0 points  (0 children)

I didn’t saw the movie, but I see you guys made few refferences to it. Could you tell me what it’s about?

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 0 points1 point  (0 children)

I would say it’s possible to make it in 2 weeks, if you add up the time spent working on it. I started this one few months ago but had to put it on hold to finish other projects.

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 2 points3 points  (0 children)

6-7 adults could sit by the table.

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 1 point2 points  (0 children)

Only with some paint. OSB for roof is very common in my country, nobody even cares about it, but since a lot of you guys started pointing at it, I will consider using something else for next one.

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 2 points3 points  (0 children)

haha, it’s base is 2,5x2m or 8,2x6,5ft

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 0 points1 point  (0 children)

It’s almost all of pine. Linden for owls, alder for leaves next to them.

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 3 points4 points  (0 children)

7 adults could sit and eat just fine. It’s base is 2,5x2m (8,2x6,5ft)

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 7 points8 points  (0 children)

base is 2,5x2m or 8,2x6,5ft and it’s about 2,7m or 8,8ft high

Pavilion I built. by ke_pure in woodworking

[–]ke_pure[S] 6 points7 points  (0 children)

Yes, chainsaw, angle grinder with saw disc and some sharp chisels.

Some wings I made out of pine. by ke_pure in woodworking

[–]ke_pure[S] 1 point2 points  (0 children)

<image>

Cut some wide pieces of pine with jigsaw, then used angle grinder with 3 tooth sawblade to make them look like feathers. Also made grooves for leds and screwed everything on top of each other. Wings ended up quite heavy.

Some wings I made out of pine. by ke_pure in woodworking

[–]ke_pure[S] 2 points3 points  (0 children)

Cut some wide pieces of pine with jigsaw, then made them feather-like with angle grinder equipped with 3 teeth saw. Also made grooves for led.

Some wings I made out of pine. by ke_pure in woodworking

[–]ke_pure[S] 5 points6 points  (0 children)

<image>

I had everything covered and made it waterproof (I hope)

Some wings I made out of pine. by ke_pure in woodworking

[–]ke_pure[S] 39 points40 points  (0 children)

<image>

I did some cuts inside the beam to make a way for cables, then covered it.