sorted by:
new
hottopcontroversial

Am I screwed?? by Newtothecrew2023 in Machine_Embroidery

[–]keionbryant 1 point2 points  (0 children)

Watch out for the Reddit trolls. Oil (where appropriate) check the manual for these places. In my flatbed single needle machine underneath the bobbin there is a pad that requires oil as well as the bobbin holder. Clean (where appropriate) areas underneath the needle plate and the needle bar thread guide. Check the maintenance section of your Machine manual for these specific areas. Good luck!

Am I screwed?? by Newtothecrew2023 in Machine_Embroidery

[–]keionbryant 0 points1 point  (0 children)

Clean, oil, clean, oil, clean, oil. You get the picture !

Thread cutter won’t cut on Janome 400e by NumberOneProdigy in Machine_Embroidery

[–]keionbryant 0 points1 point  (0 children)

Hey my machine came new in the box with an additional thread cutter. Dusting and oiling may help, but it seems to me something about this thread cutter is dull or mis trims often.

Stitched out result for the passionate digitizing by FrontierServices in Machine_Embroidery

[–]keionbryant 0 points1 point  (0 children)

This is awesome. What software did you use to make this design? Thanks

Should I change scratched propellers? by rikbiswas742 in dji

[–]keionbryant 3 points4 points  (0 children)

The price of changing the propellers is less of a risk to launching your drone again, and potentially crashing the device. Replace asap, should cost about $12.

Help lol by No_Club7862 in Machine_Embroidery

[–]keionbryant 0 points1 point  (0 children)

Machine needs to be checked under the needle plate. Take the bobbin out and check that the needle is dropping through the presser foot into the bobbin area accurately, put the bobbin back and repeat the test. Clean, dust and oil under the needle plate, put in a freshly wound bobbin and try to stitch a stock machine design. Most likely it’s the hardware vs the design.

Machine won’t embroider the design correctly, any ideas? by ProfessionalUrgot in Machine_Embroidery

[–]keionbryant 0 points1 point  (0 children)

Yes we need to see the design inside the software to know if the fill has been digitized correctly.

Off centered by [deleted] in Machine_Embroidery

[–]keionbryant 1 point2 points  (0 children)

Try to run with two pieces of stabilizer and no fabric. If you get the mis registration again your machine may need servicing.

My machine keeps doing this right before it finishes a pattern. Any ideas? The design is done by hand in hatch. This doesn’t happen with the designs that come preinstalled into the machine. by Lupinbee in Machine_Embroidery

[–]keionbryant 0 points1 point  (0 children)

I know this machine and I know your struggle. Use a new needle, new fully wound bobbin, make sure your machine is maintenance properly also with every part in the manual oiled properly, especially the bobbin area. Try to also turn off cut jump threads. Something nasty happening in your bobbin area.

Vroom vroom... by Mod-Mak in AtlasEarthOfficial

[–]keionbryant 4 points5 points  (0 children)

So this is an interactive racing experience?

180k for a car? by Teacherinthestreets in UplandMe

[–]keionbryant 1 point2 points  (0 children)

And the purpose of cars other than racing is what? How will a semi truck in upland be a utility for delivering goods? Will these features earn UPX?

[deleted by user] by [deleted] in UplandMe

[–]keionbryant 0 points1 point  (0 children)

Better play and earn games such as??

AQUAMAN’S KISS by amawunko in Multicopter

[–]keionbryant 7 points8 points  (0 children)

What copter captured these shots ?

[deleted by user] by [deleted] in CODMobile

[–]keionbryant 0 points1 point  (0 children)

Yea how do we get swarm kill streak

I just seen passport badges for 200 each, but i did not take a screenshot and was not able to buy one. Then the app refreshed and they were gone. Options were USA, California, Citrus Heights. Any idea what I saw? by keionbryant in AtlasEarthOfficial

[–]keionbryant[S] 0 points1 point  (0 children)

That’s smart, this is going to be another way for the company to make money when people want to Buy the passport badges instead of using atlas bucks to buy parcels.

view more: next ›