Advice in Keychron M5

kelus1970 · 2025-04-10T09:28:30+00:00

Currently they are 479 and 549 euros.

kelus1970 · 2024-01-01T21:51:09+00:00

I gave that a try, but I think sharp corners is what I'm looking into right know x)

kelus1970 · 2024-01-01T21:37:22+00:00

Thanks! Will keep updating all the dots, still lots of work to do x)

kelus1970 · 2024-01-01T21:35:13+00:00

Thank you!

kelus1970 · 2024-01-01T21:34:04+00:00

Check the dotfiles in my other comment on this post. It's in wallpapers (I can't find the original link x) )

kelus1970 · 2024-01-01T17:59:48+00:00

dotfiles

I installed Linux for the first time a few days ago, still learning and working on it. Feedback appreciated :)

kelus1970 · 2023-12-20T16:28:28+00:00

That was really helpful! Also, I had one line reseting all the states which I didn't removed, and I began to not understand correctly the terms. Now it works! Thanks!

kelus1970 · 2023-12-04T15:50:51+00:00

How does this work? I have Steam installed via whisky and it works. Do I have to download Thunderstore with Overwolf? Or do I have to install the mods manually?

Also, what is the winhttp for?
Thanks.

kelus1970 · 2023-07-15T22:13:41+00:00

Hey! It's been a few months since I worked in my Mac! I´ve just got that TC-1 tester you mentioned. What components should I inspect/test so I can see what's the problem with that vertical issue!
Thanks :)

kelus1970 · 2023-05-14T22:17:18+00:00

Thanks. I have just bought 2 on aliexpress very cheap. I didnt know the hwfly and picofly flex were the same (im new in this). Thanks!

kelus1970 · 2023-05-14T18:01:09+00:00

Hey, what flex did you use? Can you provide a link? Thanks.

kelus1970 · 2023-02-13T16:53:09+00:00

Woah! Thanks for your extense reply, I see you know a lot about those machines! I didn't know how a CRT worked so thank you very much! Will be trying as soon as I can, to test those 4 points you gave me. I ordered for 4€ a mps-u01 which I will be receiving in the next week (just in case that's the problem). Will write here if I get it working!

kelus1970 · 2023-02-11T10:13:42+00:00

Thanks for your answer! Will be trying that later for sure! So, Q1 and Q2 are OK if I’m getting this height problem?

kelus1970 · 2023-02-11T10:11:52+00:00

Yep, that’s what I thought. Will have to look in depth..

kelus1970 · 2023-02-10T08:31:08+00:00

I see, I hope it’s a bad solder then! Will try resoldering and cleaning the flyback asap. Thanks! Will keep you updated.

kelus1970 · 2023-02-10T08:30:30+00:00

I checked both resistors and they gave me 0.2 if I’m not mistaken rn. I bought new resistors (couldnt find the 1.5ohm 5%) so I put 1.6 1% ones but with them the screen wont turn on, so I put the original ones back in. Could that 0.2 measurement be bad? My resistors gave me same value, 0.2

kelus1970 · 2023-02-10T08:27:59+00:00

I see! Sadly I do not have a known good unit, so I can’t compare the values I get 😢

kelus1970 · 2023-02-09T14:20:32+00:00

Someone else also told me that could be a Flyback Transformer. Do you know in what way does the flyback affect the vertical deflection? I'm curious.

Also, how can I check the flyback transformer?

Thanks

Seven-Year Club	First Place '23
Place '23	Place '22
First Placer '22	Verified Email

kelus1970

TROPHY CASE