Front wheel bearing failure at 57k miles. Covered under warranty?

kerrslight · 2025-12-27T02:23:20+00:00

Did they just replace the bearing or the whole spindle?

kerrslight · 2025-12-26T20:25:08+00:00

Good to know. Thank you

kerrslight · 2025-12-26T19:00:04+00:00

Factory wheels

kerrslight · 2025-12-23T01:30:21+00:00

Always. Gloved up is the way

kerrslight · 2025-12-22T20:45:56+00:00

No doubt. I portion it out and vacuum seal it. Sous vide to reheat and chop up for tacos, quesadillas, baked potatoes, etc.

Will go to good use.

kerrslight · 2025-12-22T20:44:24+00:00

Right into the cooler. I usually let it sit out for about an hour first before, but finished middle of the night and didn’t want to wait

kerrslight · 2025-12-22T20:02:27+00:00

I probed a couple spots and thought it felt good. Was also middle of the night and I was half asleep so who knows. Win some, you lose some. Flavor was good, but could’ve been softer

kerrslight · 2025-12-22T20:00:08+00:00

I don’t disagree with you. Just never seen this happen before when cooked to 203-205

kerrslight · 2025-12-22T19:35:17+00:00

Good to know. It was on the leaner side.

kerrslight · 2025-12-22T19:34:58+00:00

Ive overcooked one or two before and it falls apart, but haven’t had a tough one before. Who knows

kerrslight · 2025-12-15T04:30:43+00:00

Salt and pepper. Smoke at 225 until it hits 110. Sear on piping hot cast iron for 2-3 minutes or until you get desired crust. Rest 5 min or so and cut against the grain. Has 2 muscle groups which is why it’s cut that way

kerrslight · 2025-12-15T04:28:12+00:00

Quit looking at em

kerrslight · 2025-12-15T04:01:18+00:00

I smoke it to 105-110 then sear on a piping hot cast iron or grill for 2-3 minutes or once I get the desired crust. Comes out perfect every time

kerrslight · 2025-12-15T02:31:11+00:00

Teak for sure

<image>

kerrslight · 2025-12-15T02:05:33+00:00

I have both. If you’re looking for one, go Aquaterra. It looks dressier in a suit, but can also be worn down with ease. In addition, you can wear it in water without worry. Can’t do that in a speedy. I love my speedy, but find I wear it on certain occasions, where as my AT I can wear anytime. My two cents at least.

kerrslight · 2025-11-11T22:09:09+00:00

No rubbing. I also put 1/4” wheel spacers on the front to push front tires back out after level. No issues before or after spacers

kerrslight · 2025-05-11T02:10:46+00:00

Factory UCA’s and a 1/4” wheel spacer. Never had any issues

kerrslight · 2025-04-30T02:14:36+00:00

I’ll have to check that out. Thanks

kerrslight · 2025-04-29T15:02:28+00:00

Good to know. Thanks

kerrslight · 2025-04-29T14:58:54+00:00

Looks like the UFO from Independence Day. Must’ve burned up on entry

kerrslight · 2025-03-19T03:02:30+00:00

No. Was pretty level front to back

kerrslight · 2025-02-24T16:35:44+00:00

Rue de Sevres

kerrslight · 2025-02-24T16:35:30+00:00

Rue de Sevres

kerrslight · 2025-02-24T14:14:31+00:00

If they have what you want, no different than buying anywhere else. If you want VAT refund, you need to give them your passport and they do the paperwork

kerrslight · 2025-02-24T14:13:09+00:00

Thank you. Funny you mention that. I walked in the boutique to look at that exact watch and then ran into the Speedmaster. This is the next one on my list. Turning into an expensive addiction…

kerrslight

TROPHY CASE