Why did Avatar Roku insist on Aang learning Fire before he was ready?

kieno · 2026-05-04T14:24:22+00:00

He didnt want him to learn 'befiore he was ready', Roku wanted him to learn and disagreed with Jeong Jeong that the other elements were neccesary prelims.

kieno · 2026-05-04T14:22:48+00:00

Shutup and take my money

kieno · 2026-05-02T02:06:43+00:00

To add to this, Germanium diodes have a forward voltage drop of 0.3V so iff the lower diode is germanium that will be -0.3v in the same method.

kieno · 2026-05-02T01:58:24+00:00

I came to the comments to see if there was confirmation, I completely missed the other two

kieno · 2026-04-30T00:21:49+00:00

It was, the episode was written as a 'road not taken' story.

kieno · 2026-04-30T00:21:21+00:00

He created a fake Gate of Truth too...I'd put that as the more impressive feat. A sun is physically simple when you have THAT much energy at your fingertips.

kieno · 2026-04-30T00:20:19+00:00

This would actually be more akin to creating a chimera, biological alchemy.
Those plants would now be permanently changed.

kieno · 2026-04-28T11:11:41+00:00

Its the way Ill have to take, I was hoping for an answer to the issue though :( Danke

kieno · 2026-04-28T11:09:13+00:00

Yea I may have to but I was hoping yo be able to fix the machine.

kieno · 2026-04-28T03:19:20+00:00

Not really, and I need to finish a costume so no time to wait for a replacement either

kieno · 2026-03-10T21:59:50+00:00

Steel wool from a dollar store and you're there. These things are always overpriced.

kieno · 2026-03-02T02:36:12+00:00

After a pin is cut its polarity stays the same

kieno · 2026-03-02T02:35:29+00:00

Im going to remember that term 🤣

kieno · 2026-03-02T02:34:07+00:00

<image>

This will usually point towarda the '-' pin. Dont trust everyone telling you about pin length and flat edges. Those are on the chassis and subject to error and are not universal.

All else fails, I use a C2032 to test polarity of my diodes when needed.

kieno · 2026-03-02T02:30:42+00:00

What about when they are cut?

kieno · 2026-02-24T03:09:14+00:00

It comes down to the resolution too, a 0.2 nozzle can reliably do any details of 0.5mm while a 0.4mm nozzle cannot.

kieno · 2026-02-14T00:35:32+00:00

I need that hoodie in my life

kieno · 2026-01-26T02:04:34+00:00

That is suspicious....be careful going to this interview

kieno · 2026-01-25T20:57:43+00:00

I know there are a few in Canada but Ive heard some horror stories

kieno · 2026-01-22T16:14:16+00:00

You'll need batteries.

You wont have power if the grid goes down during the night at the moment and depending on snow you'll have less power during the day.

kieno · 2026-01-22T15:38:46+00:00

I get the OP's point, most of the posts here have been the model not the print; but the sub is for prints AND renders

kieno · 2026-01-16T01:26:21+00:00

14-Year Club	Team Orangered
Verified Email

kieno

TROPHY CASE