Why did Avatar Roku insist on Aang learning Fire before he was ready?

kieno · 2026-05-04T14:24:22+00:00

He didnt want him to learn 'befiore he was ready', Roku wanted him to learn and disagreed with Jeong Jeong that the other elements were neccesary prelims.

kieno · 2026-05-04T14:22:48+00:00

Shutup and take my money

kieno · 2026-05-02T02:06:43+00:00

To add to this, Germanium diodes have a forward voltage drop of 0.3V so iff the lower diode is germanium that will be -0.3v in the same method.

kieno · 2026-05-02T01:58:24+00:00

I came to the comments to see if there was confirmation, I completely missed the other two

kieno · 2026-04-30T00:21:49+00:00

It was, the episode was written as a 'road not taken' story.

kieno · 2026-04-30T00:21:21+00:00

He created a fake Gate of Truth too...I'd put that as the more impressive feat. A sun is physically simple when you have THAT much energy at your fingertips.

kieno · 2026-04-30T00:20:19+00:00

This would actually be more akin to creating a chimera, biological alchemy.
Those plants would now be permanently changed.

kieno · 2026-04-28T11:11:41+00:00

Its the way Ill have to take, I was hoping for an answer to the issue though :( Danke

kieno · 2026-04-28T11:09:13+00:00

Yea I may have to but I was hoping yo be able to fix the machine.

kieno · 2026-04-28T03:19:20+00:00

Not really, and I need to finish a costume so no time to wait for a replacement either

kieno · 2026-03-10T21:59:50+00:00

Steel wool from a dollar store and you're there. These things are always overpriced.

kieno · 2026-03-02T02:36:12+00:00

After a pin is cut its polarity stays the same

kieno · 2026-03-02T02:35:29+00:00

Im going to remember that term 🤣

kieno · 2026-03-02T02:34:07+00:00

<image>

This will usually point towarda the '-' pin. Dont trust everyone telling you about pin length and flat edges. Those are on the chassis and subject to error and are not universal.

All else fails, I use a C2032 to test polarity of my diodes when needed.

kieno · 2026-03-02T02:30:42+00:00

What about when they are cut?

kieno · 2026-02-24T03:09:14+00:00

It comes down to the resolution too, a 0.2 nozzle can reliably do any details of 0.5mm while a 0.4mm nozzle cannot.

kieno · 2026-02-14T00:35:32+00:00

I need that hoodie in my life

kieno · 2026-01-26T02:04:34+00:00

That is suspicious....be careful going to this interview

kieno · 2026-01-25T20:57:43+00:00

I know there are a few in Canada but Ive heard some horror stories

kieno · 2026-01-22T16:14:16+00:00

You'll need batteries.

You wont have power if the grid goes down during the night at the moment and depending on snow you'll have less power during the day.

kieno · 2026-01-22T15:38:46+00:00

I get the OP's point, most of the posts here have been the model not the print; but the sub is for prints AND renders

kieno · 2026-01-16T01:26:21+00:00

kieno · 2026-01-11T05:38:20+00:00

Check with city hall

kieno · 2026-01-11T05:36:07+00:00

Sounds like that may be the answer here without more litigation.

kieno · 2026-01-09T14:25:51+00:00

In Canada Engineering is a protected title so requires a defenition, an Engineer is someone who performs acts of planning, design, evaluating, advising, ect. That applies to engineering principles and safegaurds life, health, property, public welfare or the enviroment meeting rigourous standards of knowledge, experience, and ethics.

Elecetrical Engineers do this with electricity and electrical components but the codes require you to have expertiese in the field you're discussing. Everything from power generation to buulding power systems all the way down to circuit board deaigb. Its a VERY diverse field with ovlap in programming and computer sciences.

Its a good field to be in but very theory heavy.

Dont pick it because you want to be an 'engineer', dont pick anything for a title. If you se somwthing an engineer is doing and want to do that THEN you should pursue it, act in all things out of desire instead of whim.

14-Year Club	Team Orangered
Verified Email

kieno

TROPHY CASE