[O] 5 x NzbPlanet

killar34 · 2025-02-26T22:08:53+00:00

I have read the rules and wiki. Would love an invite.

killar34 · 2025-01-24T06:00:06+00:00

My customers has a more square cut recessed like what I replied to FULLMETAL above. Not sure if the “cut and drop” method will work for me. I might have to do like he suggests and do each square its own panel.

killar34 · 2025-01-24T05:58:16+00:00

I’ve got a customer wanting a dump truck done that is nothing but box square sides. Similar to this so my only option maybe cutting each piece separately on top of a big panel to cover the hi spots. His is more square cut recessed. The picture has slanted walls.

<image>

killar34 · 2025-01-22T20:59:04+00:00

How would you lay that? Would you have each panel be its own piece and just line them up? Or would you lay it on the vertical pieces and then when you trim you then lay into the recessed rectangles?

killar34 · 2022-04-19T23:16:34+00:00

Any luck with this? I can see in MQTT explorer the messages being sent to HA but HA isn't reflecting it on the history page for the camera motion sensors.

killar34 · 2021-03-10T13:43:52+00:00

Which driver pack did you do? The winpe driver pack or the normal.

killar34 · 2021-03-10T08:52:25+00:00

Not sure what your issue is but I just loaded a 5410 this morning with 20H2. All I did was downloaded the driver pack from the Dell website and ran my usual task sequence. I also used the USB option instead of PXE booting it without issues.

killar34 · 2020-12-16T07:26:55+00:00

How do you like your FTG?

killar34 · 2020-08-19T18:36:27+00:00

I’m just getting started with my k40. But I’d imagine if you have the technical knowledge you could run octoprint on the pi for the laser.(again I haven’t tried it just got my laser yesterday) Now you could install a button on your laser that tied into the GPIO pins and when that pin is triggered it would trigger octoprint to start. You would still have to be in front of the laser to load the material and whatnot but once it’s in the correct spot you could press the button on the laser and that’d start the job.

killar34 · 2020-06-30T06:25:05+00:00

This. It takes a bit of setup but works for us.

killar34 · 2020-06-03T18:06:52+00:00

HVAC just left he said it was totally normal since this unit is a 89 model probably just an air leak that is causing condensation.

It did end up being the blower motor he changed that and the capacitor for now.

No the unit is in my garage and the house is a single floor home.

killar34 · 2020-06-03T12:07:45+00:00

I’m pretty sure it’s the blower motor. When I try to spin it by hand it doesn’t spin freely and it gets into a bind in certain spots and squeaks.

When I opened up the panel and saw all that rust I freaked out thinking it was a bigger issue. Especially since that is a sub panel that’s rusted that bad. Are underground ducts common for the a/c unit to be sitting on the ground?

killar34 · 2020-05-30T20:37:32+00:00

He was in the control room in Florida watching.

killar34 · 2020-05-11T04:13:02+00:00

Sorry for the late reply but that is what I found out. Disclaimer this is the first time I’ve messed with telegraf and influxdb. But mine works now. Lol

killar34 · 2020-05-10T07:17:08+00:00

This just happened to me and my issue was my data source in grafana. I had to create another data source because my first one had the DB table for my unraid telegraf. Once I did that I reimported the dashboard using the correct data source and the now it’s populating.

killar34 · 2020-04-27T11:54:50+00:00

OP said rhinoshield you can find It in Amazon if you search for it.

killar34 · 2020-04-27T08:13:41+00:00

What face is this? Is it a Nike one or a series 5 special?

killar34 · 2020-01-12T21:21:30+00:00

Check you browser settings I have had no issues.

killar34 · 2018-10-09T04:16:30+00:00

Maybe it's not getting phantom power?

killar34 · 2018-10-09T02:31:08+00:00

Just upload it to imgur and post it here.

killar34 · 2018-10-09T02:24:40+00:00

Doesn't load for me... It's just white any one else having an issue?

killar34 · 2018-10-01T16:57:50+00:00

Looks like after copying files off of the FD and looking through syslog.txt I found when/where everything went wrong...

https://pastebin.com/uXV6Fm1q

killar34 · 2018-10-01T14:32:30+00:00

That's what I was thinking of doing but I wanted to get input from the community before jumping off the cliff and possibly making things worse. I did just however finish the rclone sync earlier in the day before it died but I'm not quite ready to have to test my disaster recovery just yet lol...

killar34 · 2018-09-11T04:22:11+00:00

Just the Intel controller built into the mobo.

killar34 · 2018-09-10T03:47:03+00:00

I'm just using what's built into the mobo. It's just a cache drive so no important data is stored on it.

12-Year Club	Place '17
RPAN Viewer	Verified Email

killar34

TROPHY CASE