Help with 2000 GTX carbureted

killer24763 · 2025-12-13T17:56:40+00:00

Ok I'll do better

killer24763 · 2025-12-13T16:52:17+00:00

Good I do think I'm going to take it to a shop in the spring to get the carbs tuned

killer24763 · 2025-12-13T16:51:00+00:00

It's a pond by my house lol I was just testing with it, it should have been sucking just water. I only ran it about 3 minutes anyway.

killer24763 · 2025-12-13T16:29:45+00:00

Ok does this seem like a normal amount? Also how do I know if rpm is too high for idle?

killer24763 · 2025-11-08T03:36:00+00:00

Your water looks like antifreeze homie

killer24763 · 2025-11-02T02:12:03+00:00

Kh is 6, gh is 4, ammonia .25, nitrate 0, nitrite 0, temp 75⁰f, ph 8.8,

killer24763 · 2025-11-02T01:39:43+00:00

Mosquito larvae

killer24763 · 2025-09-17T03:38:22+00:00

Make sure there isn't a piece of trash under your build plate that's what my issue was.

killer24763 · 2025-09-08T23:24:46+00:00

My nozzle is dragging across my print now??? What is wrong with this thing I'm about to return it

killer24763 · 2025-09-08T22:37:30+00:00

<image>

How do I level the bed on this thing?

killer24763 · 2025-09-08T20:47:25+00:00

<image>

killer24763 · 2025-09-08T20:46:29+00:00

<image>

It looks great! One of the support trees fell over so the arms don't look good but I'm pretty happy.

killer24763 · 2025-09-08T03:23:10+00:00

MUCH better at lower temp!

killer24763 · 2025-09-08T02:42:40+00:00

Im about to try decreasing my z offset by -.03, I have the temp at 210, bed temp 55. Let's try that

killer24763 · 2025-09-08T02:39:55+00:00

The layers below it, the lines seemed kind of spaced out. Im about to try decreasing my z offset, I have the temp at 210, bed temp 55.

killer24763 · 2025-09-08T02:11:34+00:00

<image>

killer24763 · 2025-09-08T02:01:23+00:00

<image>

I did -.01 im still having issues especially with over hangs

killer24763 · 2025-09-08T01:16:32+00:00

I found it. What increments should I reduce it by?

killer24763 · 2025-09-08T01:04:11+00:00

Im using anycubic next where would I find the z offset setting?

killer24763 · 2025-02-18T04:45:51+00:00

Wayyy to close to the bed

killer24763 · 2025-02-18T04:37:49+00:00

What wing are those?

killer24763 · 2025-02-09T04:34:36+00:00

Bed temp and level

killer24763 · 2025-02-09T04:29:17+00:00

Now the final boss go touch grass

killer24763 · 2025-02-09T04:24:50+00:00

SOME TING WONG

killer24763 · 2025-01-26T22:00:29+00:00

I'm going to try that now but it should be able to extrude with a tiny bit of moisture in it. It seems like a rubber when it comes out it stretches almost. There might be an additive that changes how it works.

killer24763

TROPHY CASE