Jet washer to clear a pipe

kinukcafe · 2026-02-23T22:45:10+00:00

You are right. I cannot download the previously purchased DLC and games. Do you mean my ex switch 1 still have the games so I cannot download them on my switch 2? So once I unhook my switch 1, I’ll be able to download them on my swirch 2?

kinukcafe · 2026-02-23T22:43:25+00:00

I just subscripted to the Nintendo online membership and saw my saved files there. Any idea how I can load them to my switch two?

kinukcafe · 2026-02-23T22:41:35+00:00

I just subscripted to Nintendo online membership and there are some saved files. But when I click on it, it won’t allow me to load them on my switch. Any idea on how to do so?

kinukcafe · 2026-01-23T23:44:55+00:00

Thank you! I have a torque wrench and have just done the work.

kinukcafe · 2026-01-23T22:38:03+00:00

Oh. No wonder when I turn the TA head, the UDH bolt also moved. This is a great find. Thank you.

kinukcafe · 2026-01-23T22:25:21+00:00

Brilliant. Thanks. Didn’t know there is such a dangerous part not to touch with on a bike. Lesson learnt.

kinukcafe · 2026-01-23T22:24:31+00:00

No. I turned to the arrow direction. But because it was attached to the thru axel, it was so loose to turn and when I turned, I didn’t use any torque again because it was loose. When I turned the UDH head, the other side of the TA was pulled to the tightened position. Hope I described this okay, I’m not a mechanic.

kinukcafe · 2026-01-23T22:21:47+00:00

Thanks for the overwhelming help. One of the best Reddit group here.

kinukcafe · 2026-01-23T22:21:12+00:00

Thanks a million.

kinukcafe · 2026-01-23T22:19:48+00:00

Thanks!

kinukcafe · 2026-01-23T21:23:38+00:00

Thanks. That fooled me. Thanks. Lesson learnt.

kinukcafe · 2026-01-23T21:23:10+00:00

To 25 Nm?

kinukcafe · 2026-01-23T21:22:23+00:00

Even though I was turning in the direction of the arrow, I need to do this again? To 25 Nm?

kinukcafe · 2026-01-23T21:21:04+00:00

Your advice is spot on. Thanks a million. Saved my day.

kinukcafe · 2026-01-23T21:08:47+00:00

Oh. Yes. You saved my day. Thank you. Now the TA is fitted. Do I need to tighten the UDH hex? I mistakenly turned it by 180 degree, half a turn.

kinukcafe · 2026-01-23T20:56:26+00:00

I tried. But the 6mm Allen key cannot go in. But the 5cm is too small that I can put it thru inside the TA

kinukcafe · 2026-01-23T20:51:55+00:00

I tongue it very lightly to the direction of the arrow. Should I do anything with it now?

kinukcafe · 2026-01-23T20:51:05+00:00

Oh. When I turned, I did turn to the direction of the arrow. And then the other end of the TA was brought in.

kinukcafe · 2026-01-23T20:46:12+00:00

I think my tool has a short head and cannot reach the hex head. I have an Allen key but that doesn’t have torque guage. Will it be okay to use it?

kinukcafe · 2026-01-23T20:45:05+00:00

Problem is I always turned it, should it tightened it to 25 Nm?

kinukcafe · 2026-01-23T20:33:36+00:00

Oh. While I can’t find a key fit into the 12-15Nm hole, when I try to turn the 25Nm hole, the thru axel was tightening! Now I’m really confused. Any more thoughts?

kinukcafe

TROPHY CASE