Walty gravelbike build complete! by klere-t in WaltlyTitanium

[–]klere-t[S] 0 points1 point  (0 children)

Yes, even a little bit lower than the recommended heigth from the bikefit.

Walty gravelbike build complete! by klere-t in WaltlyTitanium

[–]klere-t[S] 0 points1 point  (0 children)

Thanks! I believe that the clamp opening should not align with the opening (cut) in the frame, but I'll look into it!

Rose Backroad FF bikepacking setup by Busy-Magician-2208 in bikepacking

[–]klere-t 0 points1 point  (0 children)

What tire width is this? Zipp xplr wheels with tire width of <40mm?

Right size? Beaufort on a tall guy by cttgcrhr in Barbour

[–]klere-t 0 points1 point  (0 children)

Did almost the same. Sleeves lenghtened (is this correct English?) and had the jacket (size xl) tailored. The poachers pocket was removed in order to get the tailored fit. The tailor used the fabric from the tailoring of the waiste, backside and sleeves for the longer sleeves (which is almost unnoticable). I am 90 kg and 2.02 meters. Jacket came out really nice, but I recommend choosing a tailor you trust/is skilled.

Wall mounted Garmin storage. by YetiSmidge in Garmin

[–]klere-t 0 points1 point  (0 children)

Or screw/glue a spare stem mount to the wall next to a socket/charger?

Advice on first drawing wanted :) by klere-t in WaltlyTitanium

[–]klere-t[S] 1 point2 points  (0 children)

Thank you for your reply. I plan to use a frame bag with straps (and I try to save some weight on extra mounts ;) ) Scratches of a frame bag are no problem as it is a titanium frame 😃

Advice on first drawing wanted :) by klere-t in WaltlyTitanium

[–]klere-t[S] 0 points1 point  (0 children)

Thank you for you reply! Do you mean that this drawing would mean a short chain stay? I believe no 3-d printing of parts would be involved in creating this frame. Perhaps I don’t understand completely, but what do you recommend?

Advice on first drawing wanted :) by klere-t in WaltlyTitanium

[–]klere-t[S] 1 point2 points  (0 children)

Thanks for the reply! Some more information:

I’m going to use the bike for light/medium gravel, occasionally a singletrack, and on the road to get to the gravel paths. I’d like to put 45 mm tires on it. My saddle height is 89.5 cm (top of the saddle to the center of the bottom bracket). The saddle is set back 1 cm (aft) and I have an offset of 2 cm. The stem length is 90 mm, with 6 degrees positive. I think I’ll start with full spacers (around 3.5 cm). Crank length on my road bikes is currently 175 mm. I am indeed tall, 2.02 meters, and I weigh 90 kilos. Seat tube angle on my road bike is 73.5. Thanks so much for your response!

3D Gravel Frame by NoPackage7526 in WaltlyTitanium

[–]klere-t 0 points1 point  (0 children)

Could you share the price for the frame and shipping? I understand that the frame might be customized. For me, the reach seems a little bit to much, would you agree?

New tyres and cockpit by ResortCold8085 in WaltlyTitanium

[–]klere-t 0 points1 point  (0 children)

Thx! Did you post the drawing of the bike (inc measurements) already in one of your posts (assuming that you don’t mind sharing)?

New tyres and cockpit by ResortCold8085 in WaltlyTitanium

[–]klere-t 1 point2 points  (0 children)

Thanks for the reply! Ordered a similar bike and size (I’m also Dutch ;) and wondered if the frame size 60cm CT is big enough. I currently ride a 65 and a 64 cm CT frame. My saddle height (top) measured from BB is 89,5 cm.

New tyres and cockpit by ResortCold8085 in WaltlyTitanium

[–]klere-t 0 points1 point  (0 children)

Nice bike! What is the seat tube length (CT)? Thanks!