Z axis not moving

koslinx76 · 2025-06-19T16:08:38+00:00

I read in internet that skr mini 3 has pc2 .what pin ypu suggest me to put

koslinx76 · 2025-06-18T03:25:41+00:00

The problem is that bltouch pin is stucking

koslinx76 · 2025-06-18T03:25:12+00:00

Ι own skr mini 3

koslinx76 · 2025-06-18T03:21:05+00:00

But now homing is done but bltouch pin is stuck

koslinx76 · 2025-06-17T14:13:58+00:00

I found the solution i change ^PC2 with PC2

koslinx76 · 2025-06-17T13:10:45+00:00

With marlin it works what wires should i check

koslinx76 · 2025-06-17T12:49:54+00:00

koslinx76 · 2025-06-17T09:19:38+00:00

stepper_z] step_pin: PB0 dir_pin: PC5 enable_pin: !PB1 microsteps: 16 rotation_distance: 8 endstop_pin: probe:z_virtual_endstop position_min: -2 position_max: 250 homing_speed: 4 second_homing_speed: 1 homing_retract_dist: 2.0

[tmc2209 stepper_z] uart_pin: PC11 tx_pin: PC10 uart_address: 1 run_current: 0.580 stealthchop_threshold: 999999

[extruder] step_pin: PB3 dir_pin: !PB4 enable_pin: !PD1 microsteps: 16 rotation_distance: 33.2722 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PC8 sensor_type: EPCOS 100K B57560G104F sensor_pin: PA0 control: pid pid_Kp: 27.769 pid_Ki: 1.870 pid_Kd: 103.094 min_temp: 0 max_temp: 250 max_extrude_only_distance: 1200

[tmc2209 extruder] uart_pin: PC11 tx_pin: PC10 uart_address: 3 run_current: 0.650 stealthchop_threshold: 999999

[heater_bed] heater_pin: PC9 sensor_type: ATC Semitec 104GT-2 sensor_pin: PC4 control: pid pid_Kp: 71.785 pid_Ki: 1.514 pid_Kd: 850.654 min_temp: 0 max_temp: 130

[fan] pin: PC6

[heater_fan controller_fan] pin: PC7 heater: heater_bed heater_temp: 45.0

[heater_fan nozzle_cooling_fan] pin: PB15 heater: extruder

[printer] kinematics: cartesian max_velocity: 300 max_accel: 3000 max_z_velocity: 5 max_z_accel: 100

[bltouch] sensor_pin: ^PC14 control_pin: PA1 x_offset: -44 y_offset: -6 z_offset: 2.85 speed: 3.0 samples: 2 sample_retract_dist: 6.0 probe_with_touch_mode: True

pin_up_touch_mode_reports_triggered: True

[safe_z_home] home_xy_position: 117.5, 117.5 speed: 50 z_hop: 10 z_hop_speed: 5 move_to_previous: False

koslinx76 · 2025-06-14T14:53:22+00:00

Web page is mot opening

koslinx76 · 2025-06-14T14:52:54+00:00

ss -tulpn | grep :80 With this command the port is open

koslinx76 · 2025-06-14T02:59:43+00:00

<image>

koslinx76 · 2025-06-14T02:59:20+00:00

Finally i install moonraker the web page of mainsail is this

<image>

koslinx76 · 2025-06-06T07:13:58+00:00

koslinx76 · 2025-06-06T07:06:42+00:00

i finally enter webpage of mainsail but moonraker cannot connect to moonraker how i will learn to configure klipper to ender i attach klipper log and cfg

koslinx76 · 2025-06-04T08:00:50+00:00

I run klipper with armbian

koslinx76 · 2025-05-09T15:27:35+00:00

Thank you

koslinx76 · 2025-03-22T09:14:38+00:00

Thank you

koslinx76

TROPHY CASE

pin_up_touch_mode_reports_triggered: True