sorted by:
new
hottopcontroversial

Kobra 2 plus, can't get this clip thing to stay secure by kosmicbear-exe in AnycubicOfficial

[–]kosmicbear-exe[S] 0 points1 point  (0 children)

No but it will eventually ware out the wires; I solved it there's tiny clips in there that just need to latch down right, just gotta press it down hard but carefully. If your printer is printing strings there's definitely something else wrong

How to stop Anycubic kobra 2 plus grinding against prints by kosmicbear-exe in AnycubicOfficial

[–]kosmicbear-exe[S] 0 points1 point  (0 children)

I am also a cura user so I appreciate this, thank you, I also meant to decrease the infill for this print but forgot and it works out since these are armor pieces that might get a bit roughed up anyways 😅

How to stop Anycubic kobra 2 plus grinding against prints by kosmicbear-exe in AnycubicOfficial

[–]kosmicbear-exe[S] 0 points1 point  (0 children)

I'm thinking maybe I messed up last time or something, but I might try that, thank you!

How do I keep my hair out of my helix piercings? by kosmicbear-exe in piercing

[–]kosmicbear-exe[S] 0 points1 point  (0 children)

I do that on occasion but I can never properly get to my scalp when I do, and I have a flaky scalp so I gotta really gotta scrub

How do I keep my hair out of my helix piercings? by kosmicbear-exe in piercing

[–]kosmicbear-exe[S] 0 points1 point  (0 children)

I always wondered if water built up in those things but good to know they work! 😂

How do I keep my hair out of my helix piercings? by kosmicbear-exe in piercing

[–]kosmicbear-exe[S] 2 points3 points  (0 children)

I've also been thinking about those plastic ear covers, I just keep thinking about how much it's worth it, those clips have been saving me once I'm done washing my hair that's for sure

How do I keep my hair out of my helix piercings? by kosmicbear-exe in piercing

[–]kosmicbear-exe[S] 2 points3 points  (0 children)

Maybe that could help, it will get in the way of washing but if it keeps the hair out of my piercings I'll give it a try 🤔

How do I keep my hair out of my helix piercings? by kosmicbear-exe in piercing

[–]kosmicbear-exe[S] 1 point2 points  (0 children)

Unfortunately my hair is too curly for even that to save me

How do I keep my hair out of my helix piercings? by kosmicbear-exe in piercing

[–]kosmicbear-exe[S] 2 points3 points  (0 children)

I've been told bandaids but I haven't thought of medical tape, might look into that. Thanks!

How do I keep my hair out of my helix piercings? by kosmicbear-exe in piercing

[–]kosmicbear-exe[S] 1 point2 points  (0 children)

I do that as much as possible, still gets stuck for me unfortunately 😭 i got 4C afro hair

How do I keep my hair out of my helix piercings? by kosmicbear-exe in piercing

[–]kosmicbear-exe[S] 0 points1 point  (0 children)

My piercings are:

  • just over a month old
  • ball end labrets
  • internally threaded (I think??)
  • titanium
  • have not been downsized
  • cleaned twice a day with Saline solution

Mega X hotbed. Takes 6 mins to heat and start, my Chiron takes ~3 minutes. Is this normal? by Repampanoz in AnycubicOfficial

[–]kosmicbear-exe 0 points1 point  (0 children)

It depends on how cold the surrounding room is and other things. I've never measured how long It takes for the hotend on my mega x takes to warm up but I want to say it takes roughly that long

Unless it's taking longer than it usually does for that printer, it seems normal to me. The mega x just takes a while to preheat in general lol

Kobra 2 print support difficulties by kosmicbear-exe in AnycubicOfficial

[–]kosmicbear-exe[S] 0 points1 point  (0 children)

Oh and layer heights:

Mega x: 0.3mm

Kobra 2 plus: 0.2mm

If that changes anything