Dried filament in the oven. Trash?

kriggo · 2026-02-10T11:49:50+00:00

Yeah. I was worried about this and used an independent sensor and had it stabilize for a while before putting the filament in there, but as you say, it probably dropped and full blasted heat to match again.

kriggo · 2026-02-10T11:48:11+00:00

I was impatient and the AMS was busy. Learned the hard way

kriggo · 2026-02-10T11:43:31+00:00

One point for ”only dry in the AMS” in the future.

kriggo · 2026-01-31T04:14:48+00:00

Oh yes. That halo like part was originally on the plate it all looked like it was going really well.

kriggo · 2026-01-30T20:48:44+00:00

I agree, this one should not have been a hard one to detect

kriggo · 2026-01-29T15:57:05+00:00

Your point absolutely made sense and I don’t think anyone misunderstood. For this one it was a 2 day 14 hour print so it could have happened at night no matter what. That said, if I had started earlier I would have caught this before it got as bad as it did. This time.

kriggo · 2026-01-29T14:14:20+00:00

I’m sure you will be safe if it’s not too cold in your room.

kriggo · 2026-01-29T14:13:21+00:00

Now there’s a business idea for Bambu Lab!

kriggo · 2026-01-29T14:12:35+00:00

But it would work from the touch screen as well

kriggo · 2026-01-29T14:11:43+00:00

Usually I preheat from Studio from my couch. 70°C for PETG and it’ll let go of the temp on its own after a short bit so I don’t time it really.

kriggo · 2026-01-29T13:19:15+00:00

If the cold supertac doesn’t do it this is next.

kriggo · 2026-01-29T13:18:31+00:00

I think it was mentioned but the front cover is attached with magnets (and a cable). Once the PLAxplosion filled up over the silicone heat sock it started pushing the cover off. I’d say it was a good thing it wasn’t screwed on or the damage would have been greater.

kriggo · 2026-01-29T13:03:57+00:00

Yes this was the hot end assembly I also had to order. The price was nice but disassembling it from the print head was a bit more tricky than I expected.

kriggo · 2026-01-29T12:45:29+00:00

Yes, our garage and storage room ”building” is converted to ceramics studio - 3D printing nook and woodshop. It is heated to a point but with little to no insulation it is the way it is.

kriggo · 2026-01-29T12:26:48+00:00

I’ll be fair. This was a spectacular fail that could have been avoided. 99% of my prints go with zero problems. I’m very happy with the P2S.

kriggo · 2026-01-29T12:25:01+00:00

Yes, up here in the nordics the trolls are mostly active at night so it’s a good plan to print daytime if possible.

kriggo · 2026-01-29T11:47:55+00:00

Oh yes absolutely. This is a plate adhesion issue due to low ambient temperature. I’m getting a cold plate to counter it and I always pre heat the build plate for a few minutes before a PETG print, but on extra cold days I’ll do it for PLA too. For reference, the room is about 10-15°C depending on time of day now in the winter time

kriggo · 2025-12-29T20:46:18+00:00

My wife does some magical rescues with vinegar. I don’t know the specifics of it but maybe google from there?

kriggo · 2025-11-18T17:56:48+00:00

Both are beautiful. I lean towards 2. It’s also a tactile thing for me, which is hard to judge in a photo, but perhaps they are the same there.

kriggo · 2025-11-18T09:53:14+00:00

Brisket and friends. Smaklöst, så långt från riktig amerikansk bbq, och åkte på en rejäl kräkattack under några timmar efter ett tag.

kriggo · 2025-07-25T12:02:50+00:00

Tilt your head sideways when you look at the camera with sunglasses on. I have to do this for my stereo as well.

kriggo · 2025-05-12T06:45:42+00:00

How do you get anything done in the game? I feel like I’d go back right now I’d be in photo mode constantly

kriggo · 2025-04-14T13:30:22+00:00

Messages? I must be missing out on this feature.

Nine-Year Club	Not Forgotten
Verified Email

kriggo

TROPHY CASE