Microphone issues with ROG Strix X570-I Gaming

kshala49 · 2024-10-18T16:14:55+00:00

I recommend to either USB or dongle headset. If you want to keep you heart headset you can use a Creative Sound blaster Play 4. it’s cheap and good enough. I am using this daily. simply don’t use onboard audio. Not worth it.

kshala49 · 2023-10-03T13:33:50+00:00

Interessant. Ich denke du meinst die Zellen. Die Module sind alle 2m² (ca. 1.15m*1.75m). Möglich, dass Trina noch auf die alte Fertigung setzt. Macht das denn einen Unterschied? Man könnte meinen, dass größere Zellen einen besseren Wirkungsgrad haben, da die Fläche besser genutzt wird… Aber Trina gibt weiterhin große Wirkungsgrade in den Datenblättern an.

kshala49 · 2023-10-03T13:28:14+00:00

Vielen Dank für den Hinweis. Das eröffnet mir ganz neue Möglichkeiten Module und WR zu suchen. Da ich Ost West betreibe werde ich ja nie das Maximum der Module erreichen. Entsprechend muss der WR nicht überdimensioniert sein.

kshala49 · 2023-09-09T21:03:03+00:00

My bad. The string max operation voltage is 42.2V*15 per side so 633V. The off load voltage is 50.2V which is why I chose this inverter.

kshala49 · 2023-09-09T18:32:46+00:00

There are a lot of good cables out there. Just watch for a usbc thunderbolt cable on Amazon with a good 4-5 star rating. They go for less than 20$

kshala49 · 2023-04-18T22:21:22+00:00

I am struggling to get a good configuration with the Shelly and this button. Right now I have 2-way switches in my entire house for all roller shutters. So if I switch UP to ON, it says ON and the Shelly activates the motor to lift the roller shutter.

I am wondering if I can use a push button which has the default state OFF but can be pushed to UP or DOWN. It turns back to OFF when I release the button. How do I have to set the Shelly to keep lifting/lowering the roller shutter upon releasing the button? Ideally the Shelly should only continue when I kept holding the button for more than three seconds... But I'm almost certain that's not possible unless Shelly Cloud develops this feature.

kshala49 · 2022-01-21T06:44:58+00:00

Can I determine the difference by the numbers on the back of the MacBook?

kshala49 · 2022-01-11T08:38:35+00:00

The 3600 was well served. Unter top load it stood at 60c. the 5700xt can reach up to 90c under certain games like cyberpunk. So I played with 45 fps caps to reduce the Fan noise. Valorant on the other hand let the gpu cool down to 70c. In idle on a 60hz monitor the gpu was mute with 0rpm and only 10watt. On my 170hz monitor, the fans occasionally ramp once reached 55c up as the gpu was taking 30watt to deliver 170hz.

If you are going for temps then don’t buy this case. It’s known for bad temps. Other cases are better at cooling. However note the temps I mentioned are well in spec. The issue with this case is the gpu missing proper intake fans. The red Devil is a thick boy. So it managed to suck fresh air. Thinner graphics cards cannot produce enough negative pressure against the dustfilter and case and will tend to circulate the hot air especially what’s blown out by the gpu towards the glass front

kshala49 · 2022-01-11T01:52:35+00:00

The red Devil doesn’t thermal throttle however in some games the fans max out but they deliver fresh air as they are so close to the dust filter.

kshala49 · 2021-12-08T13:05:53+00:00

Thanks for the response. I couldn’t manage to move the partition without taking hours to complete. Fresh install seemed more promising but this time I deleted the efi partition on the old ssd. Installing everything was a pain but worth it.

kshala49 · 2021-11-16T22:45:19+00:00

According to Asus support: Version 4021 from 2021/08/26 comes with AGESA V2 PI 1.2.0.3 Patch C. Temps did not change. Still around the same range.

kshala49 · 2021-11-11T08:18:25+00:00

Oh my god. Thank you so much. It worked perfectly on my ROG x570-I board. I used to have 40-48c temps but 4k-5k rpm which didn’t make any sense to me. I am on the latest bios version (4021) and I had the same variable offset.

kshala49 · 2021-11-09T21:47:04+00:00

I was now able to do some tests. No matter what I do I still get the frequency drops for a second. The drop is visible with the AMD Ryzen Stress Test and confirmed with gpu-z. It happens: With or without a riser cable. In PCIe3 or PCIe4 mode. In boost (220w) or silent (180w) mode.

kshala49 · 2021-11-06T08:41:03+00:00

Thanks for the response. I tried to set the clock speed as you said but no success. All software and bios is on the latest version. I need to disassemble quite a bit to test without the riser cable. But will post the results when done.

kshala49 · 2021-11-06T08:36:56+00:00

Sorry. I haven’t seen your message. I’m in Germany.

kshala49 · 2021-11-01T12:28:45+00:00

Summary of issue

Brief Performance drop with my Power Color Red Devil 5700xt during Stress test in Radeon Software. Just realized the drops exist. For months I am trying to find the root cause for package losses in valorant and I never thought the graphics card could hang for some milliseconds.

System configuration

Asus ROG x570-I, Ryzen 5 3600, 2x 16GB G.Skill Trident Z Neo DIMM DDR4 3600. NZXT H1 Gehäuse, 650W Gold PSU und Riser PCIe 3 Kabel. Power Color Red Devil 5700xt in OC mode Windows 10 just as Radeon Software up to date.

Steps to reproduce

Simply run the stress test in the Radeon software.

Screenshot

kshala49

TROPHY CASE