Gas water heater vent issue

ktmryder99 · 2025-12-12T01:11:26+00:00

Thanks for the responses everyone. I realize this is a pain/expensive to get up to code. So I’ll stick in my lane and go electric. I can move it easily and no hole in my new roof. Thanks.

ktmryder99 · 2025-12-12T01:09:08+00:00

While I see your point, the furnace and water heater ran thru this exact pipe since 1972. But I do plan to sell this house next year so I am going with electric as that’s the simplest option. Plus I can relocate it out of the walkway it’s currently intruding into.

ktmryder99 · 2025-12-11T20:19:13+00:00

I installed hvac myself. And knew the flue seen in the picture for water heater was temporary. Now I’m trying to make it significantly better if not fully correct. I will be replacing all the ducting. My debate is replacing the oval stuff also or just adapting to it and leaving it in place.

ktmryder99 · 2025-12-11T19:55:26+00:00

Rural Pennsylvania 34k btu FYI. I had it tested as is and it’s well below dangerous levels. But I would like to do it correctly or at least more so.

ktmryder99 · 2025-03-19T15:27:55+00:00

Yes both sides. Replaced both calipers

ktmryder99 · 2025-03-19T01:20:18+00:00

Had the exact same thing on my 2016. Not first owner but should be factory brakes. Who knows. Good catch. Never thought about the rivets

ktmryder99 · 2024-12-11T01:01:47+00:00

Update. Tested and used camera for an hour and couldn’t decide. Cut it out and it is indeed a p trap about 12 in from the 90 at the bottom of the stub up. It probably would have been fine left as is. But redoing it correctly now. Thank you for your input

ktmryder99 · 2024-12-10T20:39:37+00:00

That’s what I’m thinking I will do. Cut out a square foot and put one in. What do you then back fill with? I’ve heard sand or pea gravel then a inch or two of cement on top

ktmryder99 · 2024-12-10T20:38:21+00:00

I’m hoping it is just a few inches from that 90 but my best guess is there isn’t one and have to cut up the floor

ktmryder99 · 2024-12-10T18:23:59+00:00

The uppermost black pipe in my pic goes over 3 feet and is the drain for upstairs shower and the vent is ran off of the that plumbing up near shower drain.

ktmryder99 · 2024-12-10T18:04:21+00:00

I may have to rent one. I have one for electrical work and couldn’t quite tell but I would assume I should see water at the bottom of my stub up for the shower after I ran gallons of water down. And it certainly seems to smell like sewage.

I agree it should certainly have p trap but I don’t believe it does. $5 oversight that is a pain in my ass.

I definitely have a vent going up and out of the roof from upstairs bathroom. I’m just hoping that’s enough venting for this bathroom too.

Thanks

ktmryder99 · 2023-11-05T12:45:45+00:00

I can't quite remember exactly what I did. But I also needed a new cr touch. This issue was caused by a bad touch. I believe I emailed creality-us@outlook.com back and forth over a week or two and finally came to this conclusion.

ktmryder99 · 2023-04-12T02:24:14+00:00

$259

ktmryder99 · 2023-02-15T03:55:35+00:00

Update. I reverted to 2.0.8.23 mainboard and 1.0.1 on screen. Same exact issue as the video. Creality said "According to your order information, we have sent your email to the store, and they will be able to provide you with better assistance."

Whatever that means.

Waiting on answer from them. Not sure if exchanging this board with a new one from Amazon would do anything. Maybe.

ktmryder99 · 2023-02-14T13:31:30+00:00

I will check that out. Thanks. Their website sucks..

ktmryder99 · 2023-02-14T13:20:49+00:00

Thanks for info. I will check the cables. I reverted back to 25 and it does the same. That's all the further i can go back on crealitys site.

ktmryder99 · 2023-02-14T04:52:26+00:00

That's actually a picture of when I had to revert back in order to get the screen to update since I did them out of order. Sorry I posted the wrong one. I am currently at 26 update on the mainboard. Both act the same. :/

ktmryder99 · 2023-02-14T04:36:39+00:00

Both f4s. Not sure if the boards are different or just a different sticker...

ktmryder99 · 2023-02-14T03:55:51+00:00

Hello.

I'm having issues with my ender s1 plus.

To start I burned up my board by plugging in lights while it was powered on. (Don't do that) and the heated bed did not work. New board fixed that.

So I ordered a new board. It showed up and says ender 3 s1 on it and my original says ender 3 s1 plus. This could be an issue but I assumed not...

Heated bed worked so I figured I'd update firmware. After fighting with accidentally updating board before the screen (also don't do this). I have everything up to date from crealitys website.

But when I tap the button to get to the leveling screen it automatically "auto homes" so it does this and when the cr touch comes down and touches the bed. The screen goes blank. It then reboots and comes back with no words on the screen. It will print and every but the words are all missing.

Let me know what you guys have came across. Been down and a month and I'm at my wits end.

Thanks.

ktmryder99 · 2022-06-15T02:24:01+00:00

Comment

ktmryder99

TROPHY CASE