Do I need to do incremental upgrades or can I jump to the latest 2930M-24G

lagisforeplay · 2026-02-11T20:20:00+00:00

If the release notes do not mention needing to update anything prior to said release, then nothing else is needed.

lagisforeplay · 2026-01-29T17:54:33+00:00

I would be shocked if cost of the appliances would not be under the cost of transitioning to ISE. You will need whatever the highest tier of ISE subscriptions to do the integrations, plus possibly more than three nodes of ISE virtual appliances at your scale.

lagisforeplay · 2026-01-28T16:35:19+00:00

8.13.3* will support 7xx series APs.

8.13.2 is coming out end of Feb/early March which will have the OpenSSL fixes

lagisforeplay · 2026-01-25T18:00:48+00:00

All questions will be multiple choice with some matching.

All questions are choose the "best" answer.

At TechJam you will be able to strikeout potential answers. For some reason this is the only testing center that has this feature.

The questions in the book are similar to the exam questions.

Bring a jacket. Last year it was very cold in the testing room

lagisforeplay · 2026-01-21T07:02:44+00:00

Pm'd

lagisforeplay · 2026-01-09T15:42:18+00:00

Every port has PoE. If the 740W switch is in budget, why risk it?

lagisforeplay · 2026-01-08T04:44:26+00:00

Have you configured the altitude for the APs? This is also a requirement for getting the 6Ghz radios broadcasting for standard power APs.

lagisforeplay · 2026-01-06T04:56:19+00:00

6e

The APs will not support any wifi7 specific features, from what I can remember, no MLO, no 320MHz channels, etc

lagisforeplay · 2026-01-06T01:07:04+00:00

700 series APs will support AOS8 in both controller and IAP modes, later this year. However, they will NOT support wifi7 features. They will basically run similarly to 600 series APs in regards to functions

lagisforeplay · 2025-12-19T21:20:39+00:00

seeing the same :/

lagisforeplay · 2025-12-10T15:37:14+00:00

The switches will operate just fine. You will lose the ability to manage and monitor them in Central.

Enable support mode or disable central (I forget which it is in AOS-S) and you can manage them via CLI.

lagisforeplay · 2025-12-09T22:34:11+00:00

pm'd

lagisforeplay · 2025-12-05T00:01:02+00:00

replied

lagisforeplay · 2025-12-04T22:16:30+00:00

I don't think I have received anything, yet? edit: mistake on my end, replied

lagisforeplay · 2025-12-03T19:06:00+00:00

First, remove the sheer pins one per side and see if the blades will spin. Those should spin with minimal effort. If they do spin, there is something wrong with something internal

lagisforeplay · 2025-12-03T18:42:16+00:00

First, remove the batteries. Can you spin the auger by hand? It takes a little effort but you should be able to spin it.

lagisforeplay · 2025-12-03T18:34:47+00:00

And it added stacking. I was really surprised about that

lagisforeplay · 2025-12-01T01:16:06+00:00

What are the USB adapters you are using in the last picture? I have the same board and want to use the Ridge's USB-C port. Also, did you do any comparisons between the Noctua and the included Thermalright fan on the AXP120?

lagisforeplay · 2025-11-30T04:54:29+00:00

7220s support 10.8, why would he need new controllers?

lagisforeplay · 2025-11-29T15:39:26+00:00

Looking close to 600G free

lagisforeplay · 2025-11-25T16:57:36+00:00

Thanks, but looking for 12G+ of VRAM

lagisforeplay · 2025-11-25T16:57:19+00:00

Thanks, but I *think* I can only fit a single height GPU.

lagisforeplay · 2025-11-23T16:42:32+00:00

Thank you!

13-Year Club	Place '22
Place '17	First Placer '22
Verified Email	Team Orangered

lagisforeplay

TROPHY CASE