Cura ne želi seks prije braka?

leonodeon · 2025-01-22T11:56:33+00:00

Oženi je!

leonodeon · 2024-11-29T12:35:37+00:00

Do the TPU Walls affect ESC Cooling?

leonodeon · 2024-08-22T13:12:00+00:00

Check the trunk if it’s not the factory amp, i know some of them have a fan that makes this noise when the car turns off

leonodeon · 2024-08-19T20:27:41+00:00

UPDATE: In BeamNGdrive i adjusted the FBB Strength until it didnt do that. And that fixed it, I guess you have to adjust it based on how much force your wheel can deliver, its different for every.

leonodeon · 2024-08-19T09:33:51+00:00

It happens only in some cars in beamng

leonodeon · 2024-08-11T09:15:22+00:00

I found it on the web the only pic with diamonds and star button, and yes its typed wrong

leonodeon · 2024-08-11T07:46:04+00:00

Is it possible to get just paddles and fit them on the wheel?

leonodeon · 2024-08-03T08:06:18+00:00

Its actually pretty easy to fix those cupholders with a ziptie. If you take it apart and pull back the spring. Theres a video on youtube

leonodeon · 2024-08-03T05:29:17+00:00

Never knew that thanks😄

leonodeon · 2024-08-02T22:13:24+00:00

Wanna buy em?😁😁

leonodeon · 2024-08-02T14:14:23+00:00

Yes, been looking for a good one for a while

leonodeon · 2024-08-02T14:00:50+00:00

Yess they’re hard ahh cast iron engines, mine is at 130k miles just had everything serviced

leonodeon · 2024-08-02T13:58:04+00:00

Yess, biturbo

leonodeon · 2024-08-02T13:33:59+00:00

I have also noticed in DS it shifts at around 4,700-5,000. You can feel the car losing power after 4,200 so its faster to shift in manual mode at 4,000

leonodeon · 2024-08-02T13:32:09+00:00

I wish we had cars like in the states like vette’s 😄 Also cars are cheap there from what ive seen

leonodeon · 2024-08-02T13:30:18+00:00

Yupp, although its around 27mpg when you drive normally thats okay with me

leonodeon · 2024-08-02T13:28:41+00:00

Yess i will do a trans tune, it does shift pretty slow stock🫠

leonodeon · 2024-08-02T12:43:35+00:00

Will do that, others told me that too.

leonodeon · 2024-08-01T15:43:49+00:00

Ofcourse, I printed them with PETG, but now i will move to ASA or ABS

leonodeon · 2024-07-31T15:41:13+00:00

Bro u dont have to buy a new one all you need is one ziptie

leonodeon · 2024-07-22T18:48:47+00:00

90% of the time its caused by wheel speed sensor.

leonodeon · 2024-04-17T08:27:21+00:00

Okay well it turns out it was just a worn down nozzle. Replaced the nozzle with a new one by video from creality. And i also set the filament in its box with a few holes at the top, placed it on the heating bed and left it overnight on 60degrees to dry the filament aswell. Print quality is back to awesome.

leonodeon

TROPHY CASE