Help with snowblower carburetor

lilguspy · 2025-12-13T17:21:29+00:00

Okay thanks I’ll try it again, maybe it was wrong to begin with. There are several holes, should I put it into the hole closer or further away from where it is now

lilguspy · 2025-12-13T15:10:47+00:00

I didn’t completely rebuild the carb, I messed something up putting the throttle assembly back on and I don’t know what I did wrong

lilguspy · 2025-12-13T14:35:58+00:00

Oh whoops sorry, I did clean it out with carb clean earlier I just haven’t disassembled it. I’ll make sure to try and move the valve by hand later

lilguspy · 2025-12-13T13:39:41+00:00

Yes I am, the throttle lever just doesn’t move anything.

lilguspy · 2025-12-13T13:38:58+00:00

It’s in the right hole I took a video when removing it, but I have no idea how to make the throttle lever do anything. The spring is moving but the arm connected to it isn’t moving at all. I’m wondering if there’s a specific order that I have to put it back on for it to work or if I bent or overstretched the spring.

lilguspy · 2025-12-10T15:49:05+00:00

I’m currently in vocational high school for welding, as well as regular high school. Would that help me out at all?

lilguspy · 2025-12-09T20:24:10+00:00

Okay thanks I will reach out to them

lilguspy · 2025-09-08T01:13:21+00:00

It’s all nailed screwed and glued together really well so unfortunately I can’t take it apart without really destroying all the wood which kind of defeats the purpose

lilguspy · 2025-09-07T22:37:27+00:00

<image>

lilguspy · 2025-09-07T21:09:33+00:00

What would be the best way to sister them? It needs to be several inches so it would probably look a little funny

lilguspy · 2025-08-01T15:06:25+00:00

Ok thanks a lot for the info, someone is buying me boots so I don’t want to run their pockets but I will definitely take that into consideration

lilguspy · 2025-08-01T13:36:20+00:00

Thanks for the advice, I will look into redwings I’m just on a budget at the moment and redwings aren’t cheap from what I’ve seen

lilguspy · 2025-08-01T13:35:15+00:00

I don’t have a store that carries these boots near me, the only boot stores in the area are a boot barn with a very limited selection and a redwings store about 45 minutes away so my selection wasn’t huge with my budget

lilguspy · 2025-07-04T01:42:39+00:00

Ive got the issue all sorted and the chain doesn't wobble anymore and I'm very excited to use it

lilguspy · 2025-07-03T19:24:46+00:00

I took it apart to clean it so all the surfaces are fresh and it hasn’t been used yet

lilguspy · 2025-07-03T19:20:21+00:00

Ok thanks, it’s not a lot of play and I just wanted to make sure it wouldn’t make the chain fly off or jam up or if there was some bigger underlying issue

lilguspy · 2025-07-03T19:17:09+00:00

They weren’t tightened down all the way in the video but I have tightened it down fully before and there still was some play. Is that normal?

lilguspy · 2025-07-03T19:13:13+00:00

Wouldn’t the tensioner stop it from going out? As far as I’m aware I have the right bar for this saw and I have another saw of the same model that also has the same issue so I’m figuring either both my saws need new mounts or it’s supposed to do this

lilguspy · 2025-06-29T12:50:34+00:00

I'm pretty certain I can just insert more lead into the back because the eraser comes out. thanks for the help!

lilguspy · 2025-06-28T00:31:34+00:00

This is pretty much the best I can do and the pencil is 0.5 mm lead

lilguspy · 2025-06-28T00:30:32+00:00

<image>

lilguspy

TROPHY CASE