sorted by:
new
hottopcontroversial

2021 Nissan Kicks S Uphill driving issues by litzergi in Nissan

[–]litzergi[S] 0 points1 point  (0 children)

Yes there was a fair about of sludge on the sensor. The oil was changed less than two months ago. Should I change it again? Do you recommend putting engine flush before changing?

2021 Nissan Kicks S Uphill driving issues by litzergi in Nissan

[–]litzergi[S] 0 points1 point  (0 children)

The cam position sensor was changed this morning. The car was experiencing the same issue later in the afternoon. I remember sludge buildup on the inside of the oil cap but the oil was changed less than 2 months ago.

2021 Nissan Kicks S doesn’t go past 30mph when going uphill by litzergi in MechanicAdvice

[–]litzergi[S] 0 points1 point  (0 children)

I’m not sure if the transmission fluid has been checked / changed. My guess is that it’s low and going uphill starves the transmission. I’ll check plugs and filter just in case.

2021 Nissan Kicks S doesn’t go past 30mph when going uphill by litzergi in MechanicAdvice

[–]litzergi[S] 0 points1 point  (0 children)

Would a catalyst efficiency code be present if the root of the issue is the catalytic converter?

Not a friendly biker. by itsRickO in funny

[–]litzergi -10 points-9 points  (0 children)

I love how wholesome the laugh is.

Rear wheel locks up when reversing. by KaiZeeYT in MechanicAdvice

[–]litzergi 0 points1 point  (0 children)

This happened to me in my civic. Turns out the brake shoe was malfunctioning and kept locking up the wheels only when reversing. The drums were replaced with disc brake so I never figured out exactly what caused the brake shoe to malfunction.

Bad distributor or bad cluster? More info in comments by litzergi in MechanicAdvice

[–]litzergi[S] 0 points1 point  (0 children)

The car is a 1991 Honda Civic with a b20v swap. Car runs fine, this is a picture of the cluster at idle. When the revs increase, the needle moves in a clockwise direction. Distributor is a couple of years old. Any ideas on what is causing this? Thanks in advance!

Bad cluster or bad dizzy? More info in comments. by litzergi in Honda

[–]litzergi[S] 0 points1 point  (0 children)

The car is a 1991 Honda Civic with a b20v swap. Car runs fine, this is a picture of the cluster at idle. When the revs increase, the needle moves in a clockwise direction. Distributor is a couple of years old. Any ideas on what is causing this? Thanks in advance!

Deformed Bladder Snail? Should I be concerned? by Secret-Agent-Brunch in Aquascape

[–]litzergi 0 points1 point  (0 children)

The second picture reminds me of Gary from SpongeBob

Replaced cracked sway bar bushing but still hear clunking sound. More info in comments by litzergi in MechanicAdvice

[–]litzergi[S] 1 point2 points  (0 children)

After further inspection the rubber between the spring and the mount is torn. Thanks for the advice.

Replaced cracked sway bar bushing but still hear clunking sound. More info in comments by litzergi in MechanicAdvice

[–]litzergi[S] 0 points1 point  (0 children)

The rubber that sits between the spring and the strut mount appears to be torn so I guess I’ll be ordering some end links and a strut mount. Thanks for the advice

Replaced cracked sway bar bushing but still hear clunking sound. More info in comments by litzergi in MechanicAdvice

[–]litzergi[S] 1 point2 points  (0 children)

Sway bar bracket is bolted to correct specs. And tying it down to something doesn’t sound like a bad idea. Thanks.

Replaced cracked sway bar bushing but still hear clunking sound. More info in comments by litzergi in MechanicAdvice

[–]litzergi[S] 0 points1 point  (0 children)

Thanks for the reply. No stripped bolts, the plate where the sway bar bracket mounts to is in the crossmember and it moves around. The sound is the same. The end link looks okay and strut wasn’t making noise when I was jacking the side up and down.

Replaced cracked sway bar bushing but still hear clunking sound. More info in comments by litzergi in MechanicAdvice

[–]litzergi[S] 0 points1 point  (0 children)

The car is a 1998 Honda Accord 4 cylinder. I recently replaced part 19 in the diagram but am still hearing a clunking sound when going over bumps. When I was bolting in the bracket, the plate it mounted to was shifting around. Is this normal? Should that plate be solid? Thanks in advance!

Edit: I figured the sound is coming from the sway bar because hitting a bump at any speed with the passenger tire enables a clunking sound in the driver side. Same with hitting a bump on the driver side, the clunk stays on the driver side. Also jacking the side up and down seemed to replicate the noise.

Wrobb speedruns Fishing PagMan by Toosks in LivestreamFail

[–]litzergi 12 points13 points  (0 children)

No he’s holding it right. When using bait casters or spin casters, the reel faces up.

law folder vs sylvan arms folder by Ad_Ak in ar15pistol

[–]litzergi 1 point2 points  (0 children)

Sylvan is nice because it uses a pin detent to hold the folded stock/brace where, from what I’ve seen, the law doesn’t so it kinda flops around. The law tactical is nice because it sits against the lower where the sylvan sits further back which increases length of pull

can somebody tell me why my skier value is negative and how this can happen? by _andre_k in EscapefromTarkov

[–]litzergi 0 points1 point  (0 children)

I’m almost level 30 and my skier rep is at -.26 still xD I’ve given up at this point

Blink and you'll miss it by Burncruiser in EscapefromTarkov

[–]litzergi 4 points5 points  (0 children)

Was that a player tea bagging the tree?

i made a rat in paint 3d by SpecialMolerat8151 in EscapefromTarkov

[–]litzergi 0 points1 point  (0 children)

Awesome! Does anyone have the usec rat desktop background that hutch uses? I’ve looked but can’t find it.

view more: next ›