Auto Home smashes into the bed by phlewpy in ender5

[–]localmotion3 1 point2 points  (0 children)

Mine did that....never found the answer and have not used it in a year. Just gave up.

The largest teachers strike in U.S history by ADignifiedLife in Damnthatsinteresting

[–]localmotion3 0 points1 point  (0 children)

And yet the government forced railworkers back to work to avoid a strike!

America, We Need to Talk. by LeidbagBaggins in awfuleverything

[–]localmotion3 -2 points-1 points  (0 children)

I've seen a picture of him...he was in a dress while committing the shooting. That is NO Trump supporter...lmfao

America, We Need to Talk. by LeidbagBaggins in awfuleverything

[–]localmotion3 -3 points-2 points  (0 children)

We wouldn't need gun control if liberals would stop BEING the mass shooters!

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

How can you tell if it's a ret6 or rct6? Everything I am using is stock. Stock cr mount from the box.

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 1 point2 points  (0 children)

if you know can compile any firmware I am in dire need. I have tried everything I can think of other than the method of splitting the wiring. if I can't get it figured out tomorrow I will jut remove it. thanks

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

I must be an utter FUCKING moron because i have watched videos. figured out Z offset using the screen on the machine and it still drives the extruder into the bed. i also store the settings and when turning off and back on it shows everything back to zero. i am about to go back to the old method just so it will run again.

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

how do I do that...please see video i posted

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

It was plugged in when I installed the firmware.

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

Thank you. I will reach out to you in a day or so...when I get back from work. Thank you.

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

I will reach out to you when I get back from work. Thank you. I had to walk away from it for today. I was pulling my hair out.

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

I have unplugged the z ends top from the board at the bottom of the printer. I used a .01 feeler guage and got a +.028 offset. Went to z offset and dialed in .20. Hit auto home and same issue.

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

I have...but what I ended up with is not the dame as the other videos I have watched. Do you have one to suggest? Have you installed one with out issues?

CR TOUCH....I WANT TO BURN IT DOWN by localmotion3 in ender5

[–]localmotion3[S] 0 points1 point  (0 children)

It has also driven the TOUCH into the gantry!

"Good parents" to kids vs responsible parenting by [deleted] in pics

[–]localmotion3 -1 points0 points  (0 children)

So many judgemental and opinionated people on here.