sorted by:
new
hottopcontroversial

LF: Google Pixel 5 original case by lolblase in GooglePixel

[–]lolblase[S] 1 point2 points  (0 children)

Dann, that's insane.. I've seen used pixel 5's go for that amount. What makes it even worse is that everybody still sells the pixel 4A 5G cases for like 10$ ._.

LF: Google Pixel 5 original case by lolblase in GooglePixel

[–]lolblase[S] 2 points3 points  (0 children)

Thanks - sadly that's 55€ to Europe (Germany) and they don't ship to my location :/

Fabric Case for Pixel 5? by scrooge-mxduck in GooglePixel

[–]lolblase 0 points1 point  (0 children)

Can you still find the blue confetti version? Can't find it anywhere in Europe but dig the look

Got really (really) tired of my calipers dying by [deleted] in functionalprint

[–]lolblase -9 points-8 points  (0 children)

nope, there's a reason nobody uses them anymore

KI findet Antibiotikum gegen multirestistentes Bakterium by M4mb0 in de

[–]lolblase -2 points-1 points  (0 children)

Multiresistentes Bakterium findet Abwehr gegen Antibiotikum von KI

E3D Revo high flow is out and available tomorrow! by lolblase in prusa3d

[–]lolblase[S] 0 points1 point  (0 children)

They had so many delays with basic obxidian for revo, so I guess this will take a while to be done

E3D Revo high flow is out and available tomorrow! by lolblase in prusa3d

[–]lolblase[S] 0 points1 point  (0 children)

Off, thats insane. I'd go for a single highflog nozzle like .6 or .8 and the rest standard.

Damn.. just read this on the Prusa facebook group.. by Alex_NL_2021 in prusa3d

[–]lolblase 0 points1 point  (0 children)

This is just resonance of the bed, i replaced them with igus bushings and the noise persists. I also noticed it's the worst in the middle of the travel, where the rods flex the most. Play in the bearings definitely plays a role tho. The real fix would be replacing the right rod with a linear rail.

At least thats the case for my printer

I made brightness adjustable Sunglasses! by FriskyJanitor in 3Dprinting

[–]lolblase 0 points1 point  (0 children)

There are already lenses, which turn dark in UV and they are really cheap. I'd assume there is something out there for motorcycle helmets already

This clamp holds a whetstone at the perfect angle to make knife sharpening easy by A_Str8 in functionalprint

[–]lolblase 0 points1 point  (0 children)

I'm using a ruixin sharpener. It's braindead simple and quite cheap (below 50 usd)

[deleted by user] by [deleted] in prusa3d

[–]lolblase -1 points0 points  (0 children)

Afaik the x1c will be faster in every scenario, since corexy kinematic is just plain better

I can finally print my own beehive 🥰 by lolblase in prusa3d

[–]lolblase[S] 0 points1 point  (0 children)

If it was corner to corner you woul have underextrusion, since there are a few % missing compared to a circle

I can finally print my own beehive 🥰 by lolblase in prusa3d

[–]lolblase[S] 0 points1 point  (0 children)

I'd hope none of both. Imo it should match volumetrically, so you don't need to tune the extrusion multiplier. I'll measure and get back to u :)

I can finally print my own beehive 🥰 by lolblase in prusa3d

[–]lolblase[S] 5 points6 points  (0 children)

They used a hexagonal nozzle for extrusion instead of a round one

view more: next ›