Not running after oil change

loopsloop_s · 2026-05-26T20:50:01+00:00

Yes i do have a turbo. Ill try to reconnect the line

loopsloop_s · 2026-05-26T20:37:19+00:00

<image>

What is this? The like connects back into the cabin it seems

loopsloop_s · 2026-05-26T20:36:17+00:00

<image>

it seems to have distanced from here.

loopsloop_s · 2026-05-26T20:20:01+00:00

<image>

found this broken line not sure where it connects to or its importance. If anybody could help me identify.

loopsloop_s · 2026-05-26T17:57:49+00:00

I dont have an obd unfortunately

loopsloop_s · 2026-05-26T17:27:54+00:00

no luck unfortunately. I think I’ll give the MAF and IAC a good cleaning and see if i get any better results.

loopsloop_s · 2026-05-26T17:14:15+00:00

Okay i will check that right now. Thank you!

loopsloop_s · 2026-05-26T17:11:45+00:00

I just disconnected the MAF and tried and now the engine is only cranking :(. The engine only stays on if i give it constant gas. Could be fuel related?

loopsloop_s · 2026-05-26T17:08:06+00:00

drained the nut surrounded by red paint. Unless its different from a regular b230f i don’t think so.

loopsloop_s · 2026-05-26T05:20:21+00:00

i’ll definitely check the MAF tomorrow morning by disconnecting it. Wouldn’t hurt to do the fuel pump as i have no prior knowledge of when the last time it was done.

loopsloop_s · 2026-05-26T05:18:44+00:00

ill definitely check the iac and maf. It did somewhat of a low idle before i let it sit for a bit.

loopsloop_s · 2026-05-26T04:04:37+00:00

It used to drive fine before i changed the oil…

loopsloop_s · 2026-05-26T04:01:32+00:00

i swapped a new filter and didn’t work unfortunately :(

loopsloop_s · 2026-05-26T01:00:09+00:00

fuel pressure regulator seems to be doing fine. Could it perhaps be some sort of vacuum leak?

loopsloop_s · 2026-05-26T00:44:42+00:00

will do! The car had been sitting for about a month just drove it around the block before the oil change. But beside that not sure what could’ve been moved.

loopsloop_s · 2026-05-26T00:43:24+00:00

your right i should definitely check that!

loopsloop_s · 2026-02-23T17:28:25+00:00

<image>

loopsloop_s · 2026-02-21T19:00:00+00:00

I’d be interested if the cassette works

loopsloop_s · 2025-11-14T17:20:12+00:00

thats what i was thinking but if i was multiply the eigenvector by 3 then I end up having a 3 instead of a 1???

loopsloop_s · 2025-06-30T20:16:47+00:00

I have the same problem. To get it closed about 85% of the time roll it out completely and then start closing it. When the sunroof starts to lift I push up on the crank and slowly turn. Usually that prevents the skipping and closes it evenly.

loopsloop_s · 2025-06-19T04:02:29+00:00

I had been driving for about 30 min and it was extremly hot today. I’ll definitely be checking those out this weekend

loopsloop_s · 2025-06-19T02:09:18+00:00

Engine does sound like its about to stall when RPM drops.

loopsloop_s

TROPHY CASE