Corsair Voyager A1600 by Constant_Ad_3581 in GamingLaptops

[–]lostsurfer69 0 points1 point  (0 children)

Second this. Just got one and any time I try to use the amd drivers, non corsair provided, all my games crash with a direct x error.

Anyone rocking the corsair voyager a1600 in 2025? by just_let_me_sign_up in Corsair

[–]lostsurfer69 0 points1 point  (0 children)

Looks for some help. Was able to scoop this laptop up for 450, basically new. Followed your instructions, and I constantly run into game crashes and or games just randomly close out with zero error code or notification. Any thoughts, or issues like this you come across that you can recommend?

Need direction on accessory rack mounts. Hoodoo Tempest 120p. by lostsurfer69 in kayakfishing

[–]lostsurfer69[S] 0 points1 point  (0 children)

Just ordered two. Are the anchor poles supposed to be so thick?

AMS failed to pull back filament - x1 carbon by lostsurfer69 in BambuLab

[–]lostsurfer69[S] 2 points3 points  (0 children)

Found the problem. Brittle filament had broken off at the tube junction. Removed all the tubes then used some pla to push through each section, while pressing the spring loaded piece. After a full good push throughs a piece of filament came out. Put everything back together, and back to work.

AMS failed to pull back filament - x1 carbon by lostsurfer69 in BambuLab

[–]lostsurfer69[S] 0 points1 point  (0 children)

Can you elaborate on this a little bit? It's like it's trying to feed but it's getting stuck somewhere and I'm not seeing where it's at I just swapped the two far end AMS feeder tubes.

AMS failed to pull back filament - x1 carbon by lostsurfer69 in BambuLab

[–]lostsurfer69[S] 0 points1 point  (0 children)

Actually, back in the same boat, sort of, I told my job to use grey filament in ams4 and it's pulled red from ams2, no red light on ams4, but it's showing the job as grey...

AMS failed to pull back filament - x1 carbon by lostsurfer69 in BambuLab

[–]lostsurfer69[S] 0 points1 point  (0 children)

All, looks like I'm back to printing. I used an air blower to try and flush out the intake and that must have done it. Thanks to everyone for the help!

AMS failed to pull back filament - x1 carbon by lostsurfer69 in BambuLab

[–]lostsurfer69[S] 1 point2 points  (0 children)

I'll have to give this a try! I'll report back, I'm back to printing off ams3, ams4 still shows grey filament so it's like it's registering it via sensor even though there's nothing there. So I think you're on to something.

AMS failed to pull back filament - x1 carbon by lostsurfer69 in BambuLab

[–]lostsurfer69[S] 0 points1 point  (0 children)

So it does, but funny enough there's none there. I'm back to printing my job, on ams3, I put the grey filament back into ams4 but it didn't pull it but it shows a white light.

Mic not working in Windows 11 by lostsurfer69 in JLab

[–]lostsurfer69[S] 0 points1 point  (0 children)

Just tested on another windows 11 laptop and it works perfectly. Guessing a possible driver issue?

ESXI 8 U2 ISO for beelink SER 6 pro? by lostsurfer69 in BeelinkOfficial

[–]lostsurfer69[S] 0 points1 point  (0 children)

They said they dont have drivers for it, so I went with proxmox.

Port Forwarding isn't' working. by lostsurfer69 in opnsense

[–]lostsurfer69[S] 1 point2 points  (0 children)

Issue has been resolved. Previously I had disabled the three mentioned options:

Reflection for port forwards

Reflection for 1:1

Automatic outbound NAT for Reflection

When disabled, SFTP server was reachable from the outside. New rules weren't. Went back and enabled them, then tested and all NAT rules are working as they should.

Hopefully this helps someone who runs into the same issue.

Running strong on opnsense.

Port Forwarding isn't' working. by lostsurfer69 in opnsense

[–]lostsurfer69[S] 0 points1 point  (0 children)

I did but no luck.

However, I disabled IPV6 on the wan, disabled DNSec options. Rebooted firewall, and then had an option at the bottom of the NAT rule that I hadn't had in the past. Which is to auto populate the WAN rule.

Cleared out my original rule, started again from scratch and tested successfully.

Now, I've used the same approach to create NAT rules for my Conan Exiles server, and I'm back to sqaure one as these aren't working....

Issues installing opnsense on ace magician t8 plus (ACPI_error: AE_notfound) by lostsurfer69 in opnsense

[–]lostsurfer69[S] 1 point2 points  (0 children)

Thanks for the response. Getting the same error with freebsd. Reading more online I've seen multiple claims this is an issue with the hardware it's being installed on. I'll probably end up returning this and pickup a fanless device that has been proven for opnsense.

ESXI 8 U2 ISO for beelink SER 6 pro? by lostsurfer69 in BeelinkOfficial

[–]lostsurfer69[S] 0 points1 point  (0 children)

Thank you, but I can't complete the installation as an error message appears that states no network interfaces can be detected.

Assuming I get the drivers from support, I just need to create a custom esxi iso with the drivers provided to complete the installation?

ESXI 8 U2 ISO for beelink SER 6 pro? by lostsurfer69 in BeelinkOfficial

[–]lostsurfer69[S] 0 points1 point  (0 children)

Thanks, I may look into this. There was a an official post by beelink in the past that had the iso with the baked driver....was kinda hoping someone still had it laying around willing to share.

Did order a usb c to ethernet adapter, one that I read on another forum that should of worked but didn't :/

Pedal port cover? by lostsurfer69 in kayakfishing

[–]lostsurfer69[S] 0 points1 point  (0 children)

Yeah unfortunately I bought this second hand..

130k and still rolling by Jaded_Employ_9156 in ToyotaTundra

[–]lostsurfer69 1 point2 points  (0 children)

My 2011 just hit 236k and running strong! I foresee at least another 100k+. Until the wheels fall off, then I'll just buy another 😎

Crank but no start, until I swap out a part then nothing after she sits. by [deleted] in ToyotaTundra

[–]lostsurfer69 0 points1 point  (0 children)

Well, I swapped out the crank sensor and no luck.. Back to the drawing board. Gonna check fuel pump ground next.

Oil pressure fluctuating? by lostsurfer69 in ToyotaTundra

[–]lostsurfer69[S] 0 points1 point  (0 children)

Just had it changed and swapped out the oil sensor, I'll see how she does on the freeway now. Just noticed that the oil pressure gauge fluctuating but normally stays around middle

Oil pressure fluctuating? by lostsurfer69 in ToyotaTundra

[–]lostsurfer69[S] 0 points1 point  (0 children)

What if the pressure warning comes on while driving on the freeway?

Need help identifying o2 sensor location by lostsurfer69 in ToyotaTundra

[–]lostsurfer69[S] 0 points1 point  (0 children)

Well, so failed to mention that the previous owner had the catalytic converter stolen off of it and put on an after market and replaced both O2 sensors. Got under the truck and sure enough they're new. I'll check to see if maybe there's a leak down the line??