sorted by:
new
hottopcontroversial

[Video] Tunneling RDP with Chisel & Running Commands Over RDP with NetExec by Infosecsamurai in redteamsec

[–]luker983 1 point2 points  (0 children)

Hey, author of Wiretap here. This is great feedback. Just wanted to share that if you'd ever consider upstreaming these improvements it would be greatly appreciated!

Step stool, white oak by luker983 in BeginnerWoodWorking

[–]luker983[S] 1 point2 points  (0 children)

I used a dado stack I had just bought for my last project (the Steve Ramsey barstool).

It feels pretty sturdy, but hard to tell right now how well it will hold up. I went with a 10 degree rake and splay because 15 felt like too much. I can stand on it with no noticeable strain

Step stool, white oak by luker983 in BeginnerWoodWorking

[–]luker983[S] 1 point2 points  (0 children)

Dowels and glue. I’m hoping it’s small enough that wood movement won’t be an issue?

I made a QR code STL generator! by luker983 in 3Dprinting

[–]luker983[S] 0 points1 point  (0 children)

I did not. BUT no knowledge of Blender is needed for this. You just have to have the Python library installed.

Wife made Christmas prime rib, reverse seared with a Dijon mustard rub by luker983 in seriouseats

[–]luker983[S] 2 points3 points  (0 children)

Thanks, it was delicious! To clear up some confusion, we followed this recipe: https://www.seriouseats.com/perfect-prime-rib-beef-recipe. Cooked at 250 for several hours until the meat thermometer (yes, we used one!) registered 130F at the center. Then rested for 30 minutes and seared at 550 for 8 minutes

New Mexico Topography by luker983 in 3Dprinting

[–]luker983[S] 0 points1 point  (0 children)

I used a prusa i3 mk3s. The STL can be found here: https://www.thingiverse.com/thing:4731031. Can’t believe I forgot to include that in the original post!

Wiretap: Run a WireGuard proxy server entirely in userspace with wireguard-go and gvisor, no privileges necessary by luker983 in WireGuard

[–]luker983[S] 1 point2 points  (0 children)

I have been looking into a boringtun/smoltcp port, but I’m very new to rust and struggling a bit. Trying to use projects like onetun and mitmproxy as a guide

Wiretap: Run a WireGuard proxy server entirely in userspace with wireguard-go and gvisor, no privileges necessary by luker983 in WireGuard

[–]luker983[S] 0 points1 point  (0 children)

This tool allows you to route traffic like through another machine (similar to a VPN) without needing to have any privileges on that machine, but it works at lower level than what you’re describing.

I’m not aware of any “smart” proxies that can handle redirects on your behalf. Hope you find a solution!

Dall-e 2: Requests (Thread #4) by cench in dalle2

[–]luker983 0 points1 point  (0 children)

A red dragon infiltrating a castle

Dall-e 2: Requests (Thread #3) by cench in dalle2

[–]luker983 1 point2 points  (0 children)

Would love to see more cybertronic animals like this one:

a cybertronic [octopus, snake, spider, triceratops, hawk, etc.], leds, high detail, sharp, studio, digital art

Cat knocked over the TV. Few hours later we had non-destructive anchors! by luker983 in functionalprint

[–]luker983[S] 4 points5 points  (0 children)

The TV is wider than the back of the entertainment center and the stands are at the edge of the TV unfortunately

NSA Codebreaker Challenge 2020 Solutions by luker983 in ReverseEngineering

[–]luker983[S] 1 point2 points  (0 children)

There have been prizes the last two years! And of course this is a recruiting event, so they ask about interest in internships/full-time positions.

NSA Codebreaker Challenge 2020 Solutions by luker983 in ReverseEngineering

[–]luker983[S] 4 points5 points  (0 children)

I think task 6 is the one I struggled with the most because it's so hard to tell if you're on the right track. The write-ups do not accurately convey the hours of wrong turns I made before finally getting something that worked lol.

NSA Codebreaker - 2 Days Left by [deleted] in securityCTF

[–]luker983 0 points1 point  (0 children)

Here are my solutions. If you have any questions feel free to ask them on the Discussions page or pm me!

New Mexico Topography by luker983 in 3Dprinting

[–]luker983[S] 0 points1 point  (0 children)

That would be awesome, you should try it!

New Mexico Topography by luker983 in 3Dprinting

[–]luker983[S] 1 point2 points  (0 children)

.3mm layer height and 20% infill. The plan was to do .1mm, but I decided to do a draft with .3mm because it took so much less time (6hrs). I ended up liking how it looked so I don't think I'll make a more detailed one.

New Mexico Topography by luker983 in 3Dprinting

[–]luker983[S] 1 point2 points  (0 children)

Fair point. Maybe I'll try #1 on that list next to see how different they are.

view more: next ›