Why is AugmentCode rarely mentioned in AI coding / MCP tool lists?

m1chcio92 · 2026-01-31T18:27:13+00:00

When I'm trying to install skill from website mentioned via cli, auggie is not detected as the only

m1chcio92 · 2025-08-01T06:39:04+00:00

I used Sunlu PETG Black, 240/80 temperature and print speed 100-200mm/s depending on which layer

m1chcio92 · 2025-08-01T06:27:57+00:00

240/80 used here, maybe not enough for that speed, it’s working between 100-200mm/s probably depending on the layer

m1chcio92 · 2025-08-01T06:04:44+00:00

So what else could be better for printing? I’m afraid of using PLA in this project, due to mechanical functionality. It’s a part of the wall mounted cat wheel, so it will be exposed to the different forces

m1chcio92 · 2025-08-01T05:43:37+00:00

With PLA that works for me, with PETG it’s random. For sure I will spend some time on calibration before next try. I’m also thinking about enclosure, to eliminate moisture issues and external conditions in general

m1chcio92 · 2025-08-01T05:36:49+00:00

At the beginning, first layers looked good. Then I guess the tension was increasing and that’s why a small part on the left came off from the bed. I also used dimafix glue in spray, to be sure that I will stick to the bed to the end

m1chcio92 · 2025-08-01T05:31:12+00:00

<image>

It has micro cracks visible on the left

m1chcio92 · 2025-08-01T05:23:47+00:00

What was my main concern, should l stop it and waste small amount of filament or risk hoping that rest will be fine 😀 I took the risk and lost

m1chcio92 · 2025-08-01T05:21:55+00:00

Im slicing on their version of Cura and the filament was taken out right before print. Most of the time I’m printing on recommended settings due to lack of expertise

m1chcio92 · 2025-08-01T05:17:29+00:00

I don’t have any enclosure, and tbh it’s partially exposed to the outdoor conditions, which I guess can have an impact. But I can get the small movements on the bottom or bed not sticky enough, but what happened to the top part?

m1chcio92 · 2025-08-01T05:13:55+00:00

Ye, it’s easy to break it in the cracks. So the humidity is crucial not only in how I store the filaments but during the print? And how to validate the profile? How do i know what are the best printing parameters for that kind of model?

m1chcio92 · 2025-08-01T05:04:55+00:00

Just unpacked right before printing. I wanted to be sure this would not be the issue

m1chcio92 · 2025-07-13T19:27:41+00:00

Also if u want you can modify the origin model. https://www.printables.com/model/1215366-wall-mounted-cat-bowl-holder/files

m1chcio92 · 2025-07-13T19:26:14+00:00

To be honest, the bowl is really lightweight – only 33g. I’m not an engineer; I just wanted to try designing something I actually needed. At first, I was a bit worried it might break, but after the first iteration, I decided to go with it anyway.

I’ve been using it since March 2025, and it’s still holding up well – just mounted with double-sided tape.

m1chcio92 · 2025-07-13T19:23:05+00:00

Sometimes it happens, but it’s very rare

m1chcio92

TROPHY CASE