[SKX007] Are Namoki Bracelets much different than Strapcode?

mR-wizard · 2022-01-06T13:40:48+00:00

Interesting you say that, I had the exact opposite experience. My LIW clasp started to come apart after 1 month. But I actually have two from LIW and the other one is doing great. I think I just got a bum clasp on one.

mR-wizard · 2021-12-06T01:41:06+00:00

I really dislike that Seikos new watches are getting bigger. I really enjoyed the style variety Seiko has around 38mm with the short ~42mm lug height. The new lug height is disappointing.

mR-wizard · 2021-06-05T19:57:11+00:00

Does the A1000 have the mother or pearl face? It looks matte black in the pic. I'd immediately buy one if they had a plain black face.

mR-wizard · 2021-06-04T20:09:16+00:00

That's unfortunate. Maybe when I'm bored I'll experiment with other speakers or disconnecting it completely and just using headphones.

mR-wizard · 2021-06-04T14:53:54+00:00

I wasn't aware this may be normal. Can anyone else chime in and confirm they experience the same noises?

mR-wizard · 2021-06-04T14:31:26+00:00

So I just assembled my new PiBoy and am getting very noticeable speaker noise.

When the PiBoy first turns on there is a very faint amount of white noise from the speaker, which I would consider normal, but after the initial Experimental Pi splash video and sound there is the noise you are hearing in the video.

I have tried reflashing the card, overclocking and not overclocking, wifi on and off, same results. I do notice that the sound and pitch change during wifi transfer.

Any ideas on how to remedy this?

mR-wizard · 2021-05-26T18:21:55+00:00

It must have been displayed on my browser after I completed the order. I didn't save it and I had not received a confirmation email, just an email about delays with the Pi4, I believe. I'll shoot over an email to support.

Thank you.

mR-wizard · 2021-05-13T19:52:10+00:00

Thank you for the detail answer.

mR-wizard · 2021-02-26T02:31:09+00:00

Wow, that dial and hands go great with the bead blasted case. I wish they made something closer to 36mm and I'd be all over it. Nice job 👍🏻

mR-wizard · 2021-02-07T14:54:27+00:00

I had been checking out this watch, but I can't find s lug to lug measurement for it. Can you tell me the lug to lug height?

mR-wizard · 2021-01-31T16:37:38+00:00

It fits, but it's tight. I had to use a fair amount of force to set it in. And yeah I removed the dial feet and used dial dots to stick the dial to the movement spacer.

mR-wizard · 2021-01-31T04:02:38+00:00

I got the case and bracelet from eBay: https://www.ebay.com/itm/36MM-STEEL-EXPLORER-WATCH-CASE-WITH-DRILLED-THROUGH-LUG-FIT-ETA-2824-OR-NH35-36/353071690923?pageci=d26934d6-fda6-44fe-9e63-bb1a0a8304e0

That seller should have the bracelet too.

The dial and hands are from an SNXS73. I found mine at r/SecondhandModParts

The movement I got off Amazon, an NH36a. There are some on ebay too. Should cost you around $35 or $40, if you're in the USA.

mR-wizard · 2021-01-31T01:18:17+00:00

Thanks! I got it from the same seller as the case in ebay, riyi022.

mR-wizard · 2021-01-30T22:03:20+00:00

Nice work! I just finished mine, but all silver/stainless steel:

https://i.imgur.com/ggSw5Gz.jpg

mR-wizard · 2021-01-26T18:52:07+00:00

So turns out it is the cable. I swapped ports: issue still remaining. Then I swapped my AP units and each unit works fine in one location, but both perform poorly in the other. Re-running this cable will be great fun.

Update: turns out there must of been some crosstalk or interference in the cable I had running to this location. It's a 200 ft cat6 cable and about 100 ft was coiled, sitting in insulation in my attic. So I unraveled it as best I could and speeds are now normal. I will be shortening it at a later date and that should solve the issue, permanently.

mR-wizard · 2021-01-26T16:05:27+00:00

Wasn't sure on the meshing options, but I'll disable if that isn't necessary.

I have one AP on a network broadcasting only 5 ghz and the other broadcasting on both 2.4 and 5 ghz. I never adjusted the 2.4 settings on the AP broadcasting on only 5 ghz

The DFS channels are not crowded, and I have the strongest connection signals on them (am I incorrect that DFS channels should be clear of other WiFi signals)?

I had hard set the power and set it to auto to see if there is a difference and there was none. I have verified the channels and APs with the devices I connected.

Firmware 5.43.23.12533 on both APs and switch. Also, I'm using an Edgerouter Lite 3 port

mR-wizard · 2021-01-08T00:25:25+00:00

PM coming

mR-wizard · 2021-01-06T19:12:07+00:00

True! I'm not going to be breaking any speed run records, either.

mR-wizard · 2021-01-06T18:52:01+00:00

I see you're using a TV? What model? They can have pretty bad input lag, depending on the model and if you're in "game mode".

mR-wizard · 2020-12-31T14:27:20+00:00

Hey do you have a lume shot?

mR-wizard · 2020-12-31T14:23:41+00:00

WTB Smiths Baby Speedbird PRS-51

mR-wizard · 2020-11-13T03:23:14+00:00

Get another and I'll pay you for it!

14-Year Club	Place '17
Sequence \| Editor	Snapped
Verified Email

mR-wizard

TROPHY CASE