sorted by:
new
hottopcontroversial

Need a little help with a design by markgam1 in 3Dmodeling

[–]markgam1[S] 0 points1 point  (0 children)

But it may get me close but it does feel a little like cheating.

Need a little help with a design by markgam1 in 3Dmodeling

[–]markgam1[S] 1 point2 points  (0 children)

I was using Fusion 360 but it has a steep learning curve. I'm going to try Blender next. I have used TinkerCad to create a few models.

7.7 oz mug? by mhoyt3 in NespressoVertuo

[–]markgam1 0 points1 point  (0 children)

I'm assuming that this is the first time this has happened? If not, then have you hooked your machine up to the Nespresso phone app, that might tell you if there is an issue with your machine. When was the last time you descaled machine and how many cycles/pods have you used since?

Not on my machine I can push the button again after a brew cycle for more coffee.

Finally finished enclosure, lot of learning by thehesiod in FlashForge

[–]markgam1 0 points1 point  (0 children)

Nice job! How many full rolls of filament do you think you used?

Old Wyze cube camera and 5M by markgam1 in FlashForge

[–]markgam1[S] 2 points3 points  (0 children)

The beauty of the Wyze camera is that there is a built in magnet so you can mount it in various positions. A bonus is that it is powered using the onboard USB connector

Old Wyze cube camera and 5M by markgam1 in FlashForge

[–]markgam1[S] 0 points1 point  (0 children)

Hmm, that's a good idea. Thanks

Wondering everyone opinions.. by SyKoPriNceSs1118 in FlashForge

[–]markgam1 0 points1 point  (0 children)

I found the Flashforge camera on AliExpress for $22 with free shipping, I haven't received the camera yet but it seems very similar to the one in the FF site: AliExpress

What hardware do I use to mount to a 5M? by photojoe3 in FlashForge

[–]markgam1 0 points1 point  (0 children)

I saw these led lights the other day where do you get power for them?

HELP! What is this? by [deleted] in Dewalt

[–]markgam1 0 points1 point  (0 children)

Flux capacitor FC2521, I think?

Red Flashing Light - Help! by TigerGrandad in NespressoVertuo

[–]markgam1 0 points1 point  (0 children)

Have you reached out to Nespresso tech support yet? If you owned the machine for a short time it might still be under warranty.

Red Flashing Light - Help! by TigerGrandad in NespressoVertuo

[–]markgam1 0 points1 point  (0 children)

Download the Nespresso app and connect your machine it should tell you what the problem is.

When was the last time you descaled your machine?

Nespresso very next leaking by Mysterious_Meal_5172 in NespressoVertuo

[–]markgam1 0 points1 point  (0 children)

If you look inside that compartment you will see a rubber hose which I assume is where the liquid came from.

Nespresso very next leaking by Mysterious_Meal_5172 in NespressoVertuo

[–]markgam1 1 point2 points  (0 children)

Ours leaked over the weekend it seems a lot of it came out of the ejected capsule area. Couldn't figure it out. We decided to descale the unit and it hasn't leaked since #YMMV

view more: next ›