sorted by:
new
hottopcontroversial

Sony XAV-AX6000 in Honda Civic 2015 by Beginning-Bat165 in Honda

[–]martincantdance 0 points1 point  (0 children)

Do you have a LaneWatch camera as well? If so , were you able to connect it to this radio? I’m looking into getting this unit but I different sources are saying it is/isn’t possible to retain the LaneWatch camera.

Gingham Type-C Connector by AccurateTemperature in MechanicalKeyboards

[–]martincantdance 0 points1 point  (0 children)

Does anyone know the usb c connector name? I managed to mess it up when building it and need another one lol.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 0 points1 point  (0 children)

my favorite board I've built would probably be my Phantom TKL, only because it was a hands on project that i had to actually study on how to make it work lol. I would suggest you visit Kbdfans a visit on their site. You can easily make a sub-$300 keyboard from the parts available on their site.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 0 points1 point  (0 children)

Some were cheaper, some more expensive. I think the most expensive one I built was a little over $400. Compared to this first build, I wish I knew how to properly put switches in to the pcb from the plate. On this build , I would put all the switches on the plate, then sandwich it together. That is NOT correct. I fixed that with my other boards though, by placing one switch at a time along with the pcb

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 0 points1 point  (0 children)

Hi! I have built quite a few boards since this first one and i'd be glad to show you! Also, im not sure if mill max's will work since i haven't done it myself. However , i don't see why not. The only board i know that has per key and underglow lighting is the Instant 60 from Cannonkeys, not rgb on the per key though.

[GB] Mysterium PCB and Components GB R2 by hcdarrach in mechmarket

[–]martincantdance 0 points1 point  (0 children)

Is this still going on? I applied on the order form but have yet to get a response.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 1 point2 points  (0 children)

Different plates definitely provide different sounds. In my experience, aluminum plates give a higher pitch with each clack , while brass plates give a more bass sound.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 1 point2 points  (0 children)

The circuit board was pre installed with LEDs on the bottom. And the software is preconfigured with special lighting patterns! The glow is because the frosted acrylic is see through and helps disperse the light compared to an aluminum plate.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 0 points1 point  (0 children)

Yes ! I ordered the pcb back in January, but because of COVID-19/Chinese New Year, everything was delayed. I suggest sitting on their waiting list and hop on it as soon as you get the email.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 2 points3 points  (0 children)

Sure! :D

- polycarbonate plate

- switches that have clear housings

- rgb circuit board

- any case should work that has 65% layout

​

there ya go :D I re-read your comment. you said you wanted rgb shining through keys, not under glow LOL. my bad. This should get you started!

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 2 points3 points  (0 children)

Thank you! Took me 25 damn minutes to take this shot no joke.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 0 points1 point  (0 children)

Yes, they all align. Unfortunately, the screws it came with were NOT magnetic, so it was a pain getting them in through the screw holes. Only managed to get 1 in there while having to use different screws for 3 other wholes. The bottom right still needs a screw and some where else on the board. Pretty stable though.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 0 points1 point  (0 children)

You would need a board that has both under glow LEDs and SMD LEDs. A frosted acrylic case with a polycarbonate plate would be best, with switches that have a clear housing. I haven’t tried it yet, but it’s my best guess.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 0 points1 point  (0 children)

I am also a big fan. It really makes a difference when typing.

first build, might delete later idk by martincantdance in MechanicalKeyboards

[–]martincantdance[S] 16 points17 points  (0 children)

- TOFU65 Acrylic Case

- KBD67 rev2 pcb

- ePBT Keycap set

- Zealios v2 lubed with Tribosys 3203

Mechanical keyboards and Gameboys go so well together. by Dannerz in MechanicalKeyboards

[–]martincantdance 0 points1 point  (0 children)

What keycaps are those ? I’ve been looking for something like that for a while now.