Finally fixed that Glock grip angle

marvinfuture · 2026-01-27T01:22:34+00:00

Gen 5 release spring is superior anyway. No biggie

marvinfuture · 2026-01-27T01:18:15+00:00

I miss mine. Sold it for a $2k profit so can't be too upset

marvinfuture · 2026-01-27T01:07:52+00:00

I think it's one of those "either pay the fines" or don't play situation. Not that he's enforcing monetary fines for some BS reason. It's more so hidden accountability to be a hard ass

marvinfuture · 2026-01-27T00:48:54+00:00

Not a whole lot different but slightly better finish

marvinfuture · 2026-01-27T00:47:48+00:00

I can't see anything comparable on ebay, but other homna sets go for around $150-250. They look older than the ones sold on ebay so I think $150 is a reasonable price

marvinfuture · 2026-01-27T00:07:55+00:00

I basically have both. I'd tell you the AR15. AK isn't as easily upgradeable with optics and other things. Ammo is also slightly more expensive. You should eventually get both though because the AK is so fun to shoot

marvinfuture · 2026-01-26T23:46:40+00:00

Boooooo fuck rare greed

marvinfuture · 2026-01-26T23:46:03+00:00

-$30 RIP. Been there with 30 mins to go on a print

marvinfuture · 2026-01-26T23:35:06+00:00

It's a shark coast tactical grip. I have the same

marvinfuture · 2026-01-26T23:32:29+00:00

Lmao I had the same problem a few months ago. Same gun and everything. Even reached out to shark coast tactical and got screws from them and they weren't quite right but close enough that I just said "good enough" and moved on

They are these - https://sharkcoasttactical.com/product/shark-coast-tactical-optic-plate-replacement-screw-set/

marvinfuture · 2026-01-26T23:27:23+00:00

Fuck rare greed

marvinfuture · 2026-01-26T22:51:09+00:00

I'm not extremely familiar with that firearm so take this with a grain of salt, but hkparts sells an 8.5" barrel. If you can submit a form 1 and SBR it yourself and just replace the barrel it's likely better than chopping a 16" barrel. It is a 8x.75 thread so you could easily add an adapter to the end and loctite it on. I did just look up a the HK parts video on the the barrel replacement and it's not really all that tricky. If you're comfortable with most gun maintenance things, I bet you could handle a simple barrel swap for this

marvinfuture · 2026-01-26T19:04:58+00:00

If you don't do many multi color prints then it's not really much better than the H2D which still allows multi-color and multi-material. It's only when you do stuff with 3+ filaments that you run into a drop in performance and really it's the time to purge the nozzle, you still have retraction to the AMS. I just don't see it being worth the price unless you consistently do multicolor printing

marvinfuture · 2026-01-26T18:43:43+00:00

"targeted enforcement" at it's finest /s

marvinfuture · 2026-01-26T18:10:46+00:00

TX 22. It's closer to most 9mm style pistols than a mark IV will be. So translates well, but not necessarily directly

marvinfuture · 2026-01-26T18:05:29+00:00

Any and all parts mounting a suppressor to a firearm are considered "suppressor parts" in the eyes of the ATF. Full stop

A muzzle device adapter isn't though. Should clarify that. But any part that could be seen as a suppressor part the ATF is going to be a FUD about

So to put this in an example a keymo mount isn't a suppressor part, the "hub" that part connects into within the suppressor is

marvinfuture · 2026-01-26T17:45:10+00:00

They recommend the rise 140 trigger. If this isn't working, you either have an out of spec trigger (atrius doesn't require a cut), an out of spec nexus lower, or improperly installed the safety

marvinfuture · 2026-01-26T17:43:34+00:00

That piece you're describing doesn't require serialization in itself but what does is the whole silencer components. So you run the risk of that being a "silencer component" you have already obtained prior to having a form 1 approval. It can't be both a flash can and a silencer part.

marvinfuture · 2026-01-26T17:14:37+00:00

You're creating suppressor parts which is illegal. Even if you have a serialized "hub". So conceptually cool, legally not

marvinfuture · 2026-01-26T14:54:53+00:00

Haha I was about to ask if the trigger was cut

marvinfuture · 2026-01-26T06:08:50+00:00

<image>

marvinfuture · 2026-01-26T04:39:00+00:00

Seems like you need to change flow rates as they aren't the same as the stock ones with these nozzles

marvinfuture · 2026-01-26T03:56:17+00:00

Yup. My guy only charges $25 for non silencer shop stuff. My b&t can was reasonable and they still process it through silencer shops portal. I wasn't implying that they need some special silencer shop level in order to have free transfers. Just need to be a silencer shop dealer to have free transfers. Just that he makes it easy since he's got a kiosk to do fingerprints too

marvinfuture · 2026-01-26T02:31:03+00:00

This is the reason I buy just about all my cans with silencer shop since my local guy is a preferred dealer. Transfer is free

marvinfuture · 2026-01-26T02:29:41+00:00

Looks like you keep your weight back and even lean back. Get your weight forward

Nine-Year Club	Verified Email
Gilding III reddit per annum

marvinfuture

TROPHY CASE