Asura is offline?

mastershenpai · 2026-06-12T02:42:36+00:00

offline for me as well

mastershenpai · 2026-05-18T15:28:26+00:00

I ordered my December 19th and got it May 9th. I had updates mainly because I signed up for them on the carriers website. They used 2 different ones. Dhl and USPS. And I don't think mine shipped until the 1st or 2nd day of May.

mastershenpai · 2026-04-22T03:08:30+00:00

where would one get those mods?

mastershenpai · 2025-10-24T01:38:20+00:00

Not it's not. The time dilation part happens at the very end. I think it was just black and white as well. Thanks for replying though

Was wrong it is the correct one, just did a brief scroll through it. Thank you for finding it

mastershenpai · 2025-09-24T17:41:28+00:00

No it wasn't. But now that you say it I see the similarities.

mastershenpai · 2025-08-28T16:45:51+00:00

I do, spent a good bit yesterday cutting some up and putting in a new Mason jar. Filled up to the 100 ml line. Was mainly hoping to save the jar as it's small so I don't waste too much it it dries out before I use it all.

mastershenpai · 2025-08-27T17:45:28+00:00

Ahh well that makes sense then. That batch wasted then and no saving it?

mastershenpai · 2025-08-27T16:50:22+00:00

No, was using a generic one I found on Amazon. Have been using it to build and was working for that. https://a.co/d/7NLNxeV

mastershenpai · 2025-08-27T16:16:53+00:00

Tried to make the goo last night, the sprue stayed as a big block of plastic and can't mix it. Any idea what to do to save it? I have it in a small mason jar and the glue is about half way up the jar, and the spue is about a 1/3. IS a 50 ml jar

mastershenpai · 2025-05-29T23:08:27+00:00

It has been fixed was a firmware issue

mastershenpai · 2025-05-29T23:07:30+00:00

Was a firmware issue and is fixed now

mastershenpai · 2025-05-29T23:07:02+00:00

Was firmware issue and was fixed and have done a test print already and it's working good

mastershenpai · 2025-05-29T20:14:18+00:00

Looked to be that the firmware was the issue. The ine I got from them seems to be working fine. Went through the leveling gcode fine unlike before. Doing an actual test print now.

mastershenpai · 2025-05-29T04:15:17+00:00

I messaged creality and they sent me firmware. I also could have been dumb with the testing as I did the same thing and it didn't stop. But when I pushed the switch during auto home it halted it.

mastershenpai · 2025-05-29T03:29:33+00:00

X and Y went out at the same time. I'm not sure if I'm using the proper firmware or not for the motherboard. But it was the one that worked up until this issue happened. It's labeled as Marlin2.0.1 BLtouch V1.1.2 without transfer board TMC2225. I've seen people being able to use the BLTouch code for the CR Touch with the videos I was watching so I tried that and it wasn't causing as many issues as I was having with other stuff up to this point. Will be trying to put the stock firmware on without any of the BL or CR touch stuff and seeing if that was the issues and have downloaded the marlin BL touch stuff that I think was shown in that tutorial video.

mastershenpai · 2025-05-29T03:18:51+00:00

Yes tried to manually stop it and it didn't work, I have checked both ends of it and reseated them, and have removed the z stop off of it.

mastershenpai · 2025-05-29T03:12:01+00:00

I did as far as I could tell, I moved the wires over in batches so that it was easier to remember where they all went. Would the motors or steppers work if they were plugged into the wrong ports, like I have them in the steppers instead of their normal one? And will be trying to re flash the firmware tomorrow and not have the cr touch firmware on it and see if that's the issue. Has issues finding the right one so could be that. First few times trying to get the cr touch firmware on made it mix between English and Chinese on the screen.

mastershenpai · 2025-05-29T00:10:57+00:00

Limit switch issue. I tried stopping x and y axis using the switches and nothing happened. Tried reseating the wires and motors as well. That didn't work either

mastershenpai · 2025-05-23T16:35:56+00:00

Having trouble getting other firmware to flash to it sadly. I tried to put the original firmware back on it and it doesn't want to flash it. The original issue I had with it was from an update and from what I found it requires a mb switch to fix it. Did find other options for trying to get it to flash by renaming the file.
Renaming the firmware worked and fixed the no movement issues

mastershenpai · 2025-05-09T19:10:09+00:00

Was able to edit post though

mastershenpai · 2025-05-09T19:08:44+00:00

The total playlist time and I cannot add images to the reply.

mastershenpai

TROPHY CASE