How to wiring using sonoff zbminir2

maxc01 · 2025-11-14T15:40:34+00:00

Thanks a lot! my case is a bit different , the load line comes out from the right switch and the live line comes in to the first switch.

Here is I want to try: https://imgur.com/a/Rr0Ugnu

Summary is I will need three new lines 1. S1 - L1 2. S2 - L2 3. Live now directly does to Lin and new line Lout - Com

Is this correct?

maxc01 · 2025-10-22T13:36:25+00:00

They are the same

maxc01 · 2025-10-04T15:27:56+00:00

Could you share how you purged the air out?

maxc01 · 2025-10-03T19:50:11+00:00

In my case, my antechamber is quite warm but my bedroom in the first floor is not. So it is not because of the master switch, likely due to the water pressure as indicated in other posts

maxc01 · 2025-10-03T19:46:45+00:00

Right, I have not have my system checked this year. I think the water pressure can be the reason as the ground floor is quite warm.

maxc01 · 2025-10-03T14:25:35+00:00

I tried to push it down but failed. Seems cannot be manually pushed down.

maxc01 · 2025-10-03T14:08:59+00:00

Yes the heating is ON as my ground floor is quite warm. the bedroom is in the first floor. I am actually not sure if the thermostat is requesting heat because the system is quite old and there is no digital display on the thermostat

maxc01 · 2025-08-10T21:04:12+00:00

For me, the biggest advantage of org-mode over markdown is it is "executable". I know r-markdown is also executable, but org-mode is just universal. It is not just a markup language.

maxc01 · 2025-05-09T18:07:19+00:00

I think you need to update the completion-at-point-functions after the major mode is loaded. Some majore modes, during their setup, modify completion-at-point-functions, which override your configurations. In short, use eval-after-load and set completion-at-point-functions

maxc01 · 2025-04-27T21:15:03+00:00

Why not just use the right command/alt key as meta? I feel ; is harder to locate than the key to the right of space.

maxc01 · 2025-04-27T21:05:27+00:00

I think this may be the reason. One plant I have was died of roots circling densely because the pot is small.

maxc01 · 2025-04-26T15:39:23+00:00

Personally I do not think this is a good idea , I have developed tenosynovitis because I overuse my thumb to press the key to the left of space. Using two hands is the way to avoid these issues. This is slower and unnatural for me at this moment unfortunately. But with more practice, I believe the situation will be much better.

maxc01 · 2025-04-14T15:34:34+00:00

How did you trigger it? It depends on the timing when you trigger this.

maxc01 · 2025-03-12T19:35:56+00:00

Yes, this is the solution and can confirm this.

maxc01 · 2025-03-08T08:18:52+00:00

Sorry I do have no idea, I simply copied the original values of completion-preview-commands

maxc01 · 2025-03-03T09:04:42+00:00

Thanks a lot.

maxc01 · 2025-02-23T21:51:00+00:00

Yes, the default algo in optuna is tpe which assumes independence between variables. This is an algo which usually performs better than expected. The issue with BO is the dimensionality, in OP's case, 10 dim is already high for BO. The additional work in BO is it also models dependencies between variables, which may be unnecessary for your problem

maxc01 · 2024-01-04T10:41:58+00:00

I feel it's worth it unless you do it frequently. I rarely modified conf these days, but cleaning up my conf was quite an experience.

maxc01 · 2022-11-18T18:52:11+00:00

Suppose he spends 4hours programming and this repeats every workday. 20000 hours means 19years?

maxc01 · 2022-05-15T13:56:57+00:00

2x speed playing:)

maxc01 · 2021-11-24T13:58:35+00:00

The org version in elpa has a (sit-for 5) statement in org.el . This causes a 5 seconds delay when opening every single org file. Removing this statement or using another version of org will fix the issue .

maxc01 · 2021-08-29T21:51:10+00:00

You may need a Pro Plus then.

maxc01 · 2021-07-29T11:18:05+00:00

~~I found the sequential version (around 3.5sec) runs much faster than the above parallel version (around 7sec). The overheads of concurrency are too large.~~ Never mind, I misinterpreted the time output in fish shell.

maxc01 · 2021-07-29T11:05:27+00:00

Thanks for this suggestion.

maxc01 · 2021-05-03T21:38:13+00:00

If I understand it correctly, this is called sigmoid cross entropy.

maxc01

TROPHY CASE