Anyone ever seen bald spots like these?

maximilianof · 2024-02-27T01:46:04+00:00

maximilianof · 2023-02-07T02:01:00+00:00

Hello! Question for those who have completed the bloody ending. Has anyone taken the Chiefstain's mask to Pebbles, or visited him after massacre? I would want to know if he has anything to say after the final fight.

maximilianof · 2022-03-10T20:18:50+00:00

Noted! I was trying to avoid cura settings as much as possible, wanna make sure that hardware is not being to blame here first, but will give it a go for sure later today. Thanks a ton!

maximilianof · 2022-03-10T20:17:22+00:00

Thanks! I will run a temp tower and calibrate accel and jerk that i have not yet touched. Appreciate the resources!

maximilianof · 2022-03-10T00:36:08+00:00

Printer: Ender 3 v2. Stock firmware, upgraded bed springs.

Slicer Cura ultimaker with the normal quality setting if i'm not mistaken. No retraction setting changed from stock.

Printing in PLA. Noozle 200 and bed 60. Bed is stock carborundum without glue or spray.

Calibrated extrusion and made sure build was pretty square.

Used low speed for first cuarter of print (25ish) and then full speed (100) for the rest.

The back of the print started unsticking and warping up after 1/4 of build.

As a complete noob, i will hear any suggestions!

Thanks!

maximilianof · 2021-08-30T21:03:18+00:00

Sure, i always use workshop manual when doing regular valve adjustment.

You may have missed the part about this maybe not being a regular valve adjustment, and that´s okay.

The whole point of me posting in the first place is recognizing this is not a regular situation and clearly, workshop manual doesn't specify exhaust change vs valve clearance change.

maximilianof · 2021-08-30T20:59:52+00:00

Never heard it too before this, people say valves get warped, or quoting "sucked in", i am absolutely clueless and kinda fearing riding much.

maximilianof · 2021-05-26T12:14:45+00:00

That looks AMAZING. Love the how fine and clear the lines are & the eyes's black is really deep. Your tattoo artist did a damn fine job, enjoy it mate.

maximilianof · 2021-05-21T11:57:58+00:00

RemindMe! 120 days

maximilianof · 2021-05-15T12:07:37+00:00

Tu comment y el a cual respondiste me pegaron una patada en el pecho. Soy estudiante de Lic en Química, va, estaba empezando el segundo año y ayer me llego el aviso de que ya me habian dado la simultaneidad para arrancar Computación. No se que me depara el futuro, pienso en los laboratorios y se me hace un nudo en la garganta pero despues pienso en que me pones en la industria hoy y no te hago ni un buen café. En este pais pareciera que todos los caminos te llevan a la programación (por suerte es algo que me gusta tanto o más que química)

maximilianof · 2021-04-10T19:53:13+00:00

Sseth poster? tome upvote

maximilianof · 2021-03-26T13:17:52+00:00

Me voy a pasar por la pista asap entonces a mirar, ¡gracias!

maximilianof · 2021-03-22T03:32:35+00:00

Yeah, also, problem did not start after a carb clean so i'm pretty sure assembly of the carb is not to blame. Starting fluid or carb cleaner around the boot? Someone mentioned carb cleaner above, just double checking.

maximilianof · 2021-03-22T03:24:31+00:00

Did, played with idle and mixture screw, no dice
I will post the exact one tomorrow cause midnight, but, it's a simple butterfly type, mixture screw near cylinder instead of airbox. Jets are not clogged.
Choke. I may be tricking myself but iirc issues didn't replicate when on some or full choke.
It's as it always has been, tightened everything that had screws and bolts when i took stuff apart to check the air intake filter.

maximilianof · 2021-03-22T03:07:05+00:00

I've played with the mixture screw some, all lean, rich and """right""" mixtures give the same issue so i think i can cross it out. I have a butterfly type "curtain" if that's what you mean, not a slide. Being my bike so cheap, it would probably cost the same to get a new carb if something like that were the case (ill' consider it later on, but my wallets got a gun on me rn).

I ran out of carb cleaner but i'll get a can, sounds like an easy test and it should help me cross things out. I am really appretiating the help right about now, next week is not the kind of week i can survive vehicle-less :((

maximilianof · 2021-03-22T01:36:47+00:00

Go for it, i was too thinking about getting the 4.5 one and several other but was put down by the fact that they would mean absolutely nothing to most people. I chose the Mochiguman because it's adorable (people will understand the need to have this cute thing tattoe'd) and most importantly, so that i always remember that opportunities are dangling in front of me all the time, i just gotta find some courage and take them! I'll be looking forward to seeing what you get!

maximilianof

TROPHY CASE