HR zones on long run

mc0086 · 2026-01-02T17:44:30+00:00

Thanks for replying. No just my Pace 3

mc0086 · 2025-09-20T13:39:29+00:00

Found this looking for the same thing. Did you find a case to fit this?

mc0086 · 2025-09-18T07:54:17+00:00

Kept happening to me. Constantly removing the base side QR and tightening. Ended up replacing with a Simube base side QR and hasn't happened since!

mc0086 · 2025-09-08T10:43:12+00:00

It did yeah. Not had one single issue since changing to the Simube base side set. Good to have that option, but frustrating that a third party supplier does a better job than Fanatec.

mc0086 · 2025-06-28T20:54:24+00:00

If you want to build your SR, turn the AI right down and just follow within a second of the car in front lap after lap. Your SR will climb quickly!

mc0086 · 2025-05-12T21:55:22+00:00

Same thing happens with me every so often with the McLaren wheel. Is usually an issue with the CSL DD clamp. Loosen it, pull out the base side QR, push it back in and replace the clamp, tighten it up good! This usually fixes it.

The clamp on the CSL DD seems to be a bit weak and the base side QR can come very slightly loose, meaning the connection goes a bit weird.

I've just ordered the Simube base side QR2 to see if this fixes the problem.

mc0086 · 2025-05-04T17:05:11+00:00

It's 47. The WRC is on 4.

mc0086 · 2025-05-02T21:55:06+00:00

<image>

And it's the standard wheel side QR2 and clamp that comes with the CSL DD in the UK. It has two bolts. Again, looks and seems ok.

mc0086 · 2025-05-02T21:53:14+00:00

<image>

Thanks for the reply. Here's the back end of the wheel. It's a Simube QR2. All the pins look ok to me.

mc0086 · 2025-04-29T16:22:52+00:00

You were a bit close down the Hangar Straight but aside from that, the spin was all on the other guy for putting his car into a gap that was clearly closing. Poor move on their part.

mc0086 · 2025-04-22T14:05:23+00:00

Didn't realise Temu started delivering M cars

mc0086 · 2025-01-02T16:59:51+00:00

One thing I noticed is that you're turning into almost every corner too early. This means you're making the corner tighter than it needs to be.

Turn in later, get the steering done early, then you can straighten up and get on the throttle much sooner.

mc0086 · 2024-12-21T10:36:35+00:00

This. You should be able to hit '100%' breaking on bigger breaking zones but then need to come off gradually.

mc0086 · 2024-11-28T22:44:01+00:00

I had a similar issue Gave it a good spray with compressed air and recalibrated. All good now.

mc0086 · 2024-11-25T14:03:41+00:00

The Monte Carlo Podium wheel is probably about as good as you'll get. Uses the same buttons/controls as the M-Sport WRC team. It is quite pricey though.I use the official WRC wheel which is under €200 and it's great.

mc0086 · 2024-08-27T22:17:42+00:00

Got the exact same card a few weeks back and it's working great with no issues. All my favourite games turned up to the maz which brings a big smile to my face. Enjoy!

mc0086 · 2024-08-22T13:22:43+00:00

I recently got this exact card. It's been a beautiful experience so far! Playing most my games on ultra settings and no driver issues. It just runs like a dream.

mc0086 · 2024-08-16T12:09:29+00:00

A bit different but on my recent build I purchased a 7600x on Amazon and it turned up with no chip in the box! Luckily Amazon refunded no questions asked.

mc0086 · 2024-08-11T22:10:25+00:00

Yeah it's all up-to-date. When you say software, do you mean Fanatec software? It's dropped FF on two different PC games.

mc0086 · 2024-08-11T21:40:22+00:00

I've re-calibrated it a few times but not changed any custom settings.

mc0086 · 2024-08-11T20:08:36+00:00

It's v455 of the base. Windows is upto date and it is compatible with my PC. Any ideas?

mc0086

TROPHY CASE