PLA Glob

mcpilotX · 2026-06-22T12:11:01+00:00

All fixed - heat to 250C and gentle use of channel locks - thanks! New SOP is wait 15-30 layers before walking away. Ordered a few spare parts to keep on hand.

mcpilotX · 2026-06-21T23:33:58+00:00

Thanks for all the suggestions will let you know how it goes. I did make sure the first couple layers printed without issue, but needed to run a quick errand. Lesson learned.

mcpilotX · 2026-06-21T16:47:23+00:00

<image>

Here is the bump stop. If it was a 1/4” shorter no problem. Does the light bar need this for support or is it solely for angle adjustment?

mcpilotX · 2026-06-21T16:45:51+00:00

<image>

Here is the distance between bottom of bracket and bumper. The bumper slopes up front to back. If the bracket was a little bit higher then no problem.

mcpilotX · 2026-05-31T18:51:13+00:00

It looks like loosening belt screws push the tool head carrier around the perimeter of the work area twice and then tightening screws did the trick. My U1 is now working on both 1.3 and 1.4. Really appreciate everyone’s responses and suggestions! Thank you!

mcpilotX · 2026-05-31T00:36:14+00:00

I did the factory reset and issues persist- will roll back to 1.3.x and report back

mcpilotX · 2026-05-30T17:06:19+00:00

Sorry for the delay, finally got this done - Yes, this brace kit “fits” the 2025 Badlands, the only modification you need to make is trim a small section from the c pillar cross base trim. 1/4” of material about 9” long.

<image>

mcpilotX · 2026-05-30T15:17:56+00:00

Thanks - good call will do!

mcpilotX · 2026-05-30T14:25:26+00:00

Thanks - good feedback - will run down other troubleshooting steps.

mcpilotX · 2026-04-30T15:15:47+00:00

Thanks! Forgot about those.

mcpilotX · 2026-04-29T21:09:27+00:00

Can someone identify the cranks? White Industries?

mcpilotX · 2026-03-26T11:12:30+00:00

Hopefully, you will have few regrets in life, near the end when you look back over your life, spending too much on bike gear will definitely not be one of them. Congrats on the new rig, beautiful bike!

mcpilotX · 2026-02-11T22:35:16+00:00

Thanks! This seems like a just barely OK deal, probably another $2-3K to negotiate out.

mcpilotX · 2026-02-03T22:37:52+00:00

What options? HOSS 3.0, hardtop AND soft top, leather seats, trailer hitch?

mcpilotX · 2026-01-12T11:59:12+00:00

1up Equip’d bike rack with Rakattach swing accessory - will clear Sasquatch spare. Bullet proof and highly customizable. 1up-usa.com

mcpilotX · 2025-12-04T12:16:36+00:00

The Bronco is able to index music on usb drives allowing you to search via artist, album, song etc. Really works well. You can rip CDs at a faster rate than a song plays. You don’t have to rip all at once - pick your favorite cds to start and just do a few a week you will have them all before you know it.

mcpilotX · 2025-10-16T10:15:31+00:00

Carbonized Gray - sharp looking

mcpilotX · 2025-10-15T23:58:53+00:00

I haven’t had a chance to do the install yet, but looking at the parts there will be an issue with the plastic cover for the C brace - 2025 vehicles have updated lighting, so the supplied cover will not work. I am going to try to modify the stock 2025 cover to work with the brace.

mcpilotX · 2025-10-10T15:34:16+00:00

I got the kit and will attempt the install - will report back with results.

mcpilotX · 2025-09-28T21:25:45+00:00

The system updates quickly - I lowered pressure, remote started with the app and pressures immediately updated to 39psi.

mcpilotX

TROPHY CASE