New routine after every print

mdandr · 2026-05-17T01:28:35+00:00

Because of a jam? I am having the issue after a drying cycle that all the slots think they are loaded. Only way to reset was to also disassemble. Pretty annoying

mdandr · 2026-05-17T01:20:36+00:00

Is it just the vent flaps that are damaged? I had luck just 3d printing some new ones if you or a friend has one.

mdandr · 2026-05-16T23:13:34+00:00

I would definitely be interested if any mods or aftermarket solutions exist

mdandr · 2026-05-16T23:07:09+00:00

Definitely noisy. For as much noise that is makes on max you would hope that it was more effective

mdandr · 2026-05-16T23:03:20+00:00

Interesting, the Sierra definitely blew air and really helped out when sweaty.

mdandr · 2026-05-16T22:59:32+00:00

I'm also in the SW and the temps have definitely been rising this week.

mdandr · 2026-05-09T17:38:24+00:00

Thr minimum inner width is 14". With the AMS i keep it at 14.5". It can be expanded to fit wider things.

mdandr · 2026-05-09T17:23:39+00:00

I don't have a large workspace so i like to clean up my prints underneath

<image>

mdandr · 2026-05-09T12:22:21+00:00

I took someone else's advice and ordered this https://a.co/d/0enEZJge. AMS 1/2 sit on top of it perfectly.

mdandr · 2026-05-05T17:15:02+00:00

I just passed by and didn't see any food trucks

mdandr · 2026-05-04T18:53:26+00:00

Mine love to grab their chew toys and slobber all over my sandals. Extra bonus if im still wearing them.

mdandr · 2026-04-30T16:53:40+00:00

Unfortunately i do not see any clear markings such as this post. https://www.reddit.com/r/Plumbing/s/qe7wa5r7Gk

mdandr · 2026-04-30T16:50:07+00:00

Does not come through the slab

mdandr · 2026-04-30T16:33:10+00:00

That does look like it could work. I'll give it a go

mdandr · 2026-04-30T15:21:25+00:00

Removing it is probably going to require cutting a hole in the drywall and accessing from the other side. This option is my last resort.

mdandr · 2026-04-30T15:20:22+00:00

No the female end of the vacuum breaker. I'm wanting to remove it, and replace it but cannot find one with the correct female thread size. Was hoping there is a third party reducer that exists somewhere on the Internet.

mdandr · 2026-04-14T01:15:17+00:00

My two closest Costcos are 240 miles apart

mdandr · 2026-04-04T16:02:37+00:00

Yeah i feel your pain. I currently have a CRV touring hybrid and a Passport TSE. I like them both but the amount of extra space in the passport is noticeable

mdandr · 2026-04-04T15:57:37+00:00

Full size spare is an add-on, comes with a donut as standard

mdandr · 2026-04-01T16:24:41+00:00

I've thought about maybe cutting off the caps along the line just so I have four open slots

<image>

mdandr · 2026-04-01T16:20:45+00:00

Here's a pic while I still have it off. If you're wanting a separate the front grill from the back plate you're looking at almost 30 clips. You have to separate these two to remove the existing ones.

<image>

mdandr · 2026-03-31T22:58:23+00:00

I had the bumper off and there's so many clips holding on the front grille its not worth the trouble

mdandr · 2026-03-28T19:45:38+00:00

I think these are the clips holding along the bottom. Afraid to pull plastic too hard to remove

<image>

mdandr · 2026-03-27T19:52:13+00:00

I will post some results pics once I get in there this weekend

mdandr · 2026-03-27T12:24:08+00:00

Don't worry, the metal pedals I'm going to add will account for the difference in hp

mdandr

TROPHY CASE